Troubleshooting

If a problem should arise, first check the following:1.Are the connections correct ?2.Is the set being operated as described in the operating instructions ?3.Are the other components operating properly ?

If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.

In this case, disconnect the power immediately and contact your store of purchase.

Symptom

 

Cause

 

 

 

Measures

 

 

Page

When the power

• The power cord’s plug is not fully

• Check

the

insertion

of

the

8

is turned on, the

plugged in.

 

 

 

power cord plug and connected

 

power indicator

 

 

 

 

 

securely.

 

 

 

 

does not light

 

 

 

 

 

 

 

 

 

 

 

and no sound is

 

 

 

 

 

 

 

 

 

 

 

produced.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The power

• The

speaker

cables

are

not

• Connect securely.

 

 

5

indicator lights

properly connected.

 

 

 

 

 

 

 

 

but no sound is

• The function (input) is incorrect.

• Switch

to the correct

function

9

produced.

 

 

 

 

 

(input).

 

 

 

 

 

 

• The volume is set too low.

 

• Adjust

the

volume

to

an

9

 

 

 

 

 

 

appropriate level.

 

 

 

 

 

 

 

 

 

 

 

 

 

No sound is

• The

speaker

cables

are

not

• Connect securely.

 

 

5

produced from

properly connected.

 

 

 

 

 

 

 

 

one side.

• The input cables are not properly

• Connect securely.

 

 

6, 7

 

connected.

 

 

 

 

 

 

 

 

 

 

• The left/right balance is off.

 

• Adjust the left/right balance.

 

9

 

 

 

 

 

 

 

For stereo

• The connections of the speaker

• Check

and

remedy

the

5

sources, the

cables or input cables are

connections.

 

 

 

 

positions of the

inverted.

 

 

 

 

 

 

 

 

 

instruments are

 

 

 

 

 

 

 

 

 

 

 

inverted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Buzzing noise in

• The antenna cable is not properly

• Connect the antenna properly.

6

FM broadcasts.

connected.

 

 

 

 

 

 

 

 

 

 

• Noise interference from a nearby

• Reposition the equipment or the

6

 

electronic device equipped with

positions or directions of the

 

 

a microprocessor, or the radio

connection cables, antenna, etc.

 

 

broadcast signal is weak.

 

• Connect an outdoor antenna.

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGLISH

 

 

 

 

 

 

 

 

 

 

 

 

 

Symptom

 

 

Cause

 

 

Measures

 

Page

 

 

Getting

Hissing or buzzing

• Noise

interference

from a

• Turn off the monitor.

 

 

 

 

 

 

 

noise is heard in

nearby

monitor, etc.,

or

there

• Change the position or direction

 

6

 

 

Started

AM broadcasts.

is interference in the broadcast

of the AM loop antenna.

 

 

 

 

 

 

 

 

 

 

signal.

 

 

 

 

• Connect an outdoor antenna.

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Humming noise

• There

is

interference

from

• Connect an outdoor antenna.

 

6

 

 

Connections

is heard in AM

current in power cords.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

broadcasts.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When playing

• The player and speakers are too

• Move the player and speakers as

 

7

 

 

 

records, a wailing

close together.

 

 

far apart as possible.

 

 

 

 

Operation

noise (howling) is

• The floor

is soft and

vibrates

• Use cushions or spikes to absorb

 

 

 

 

 

 

 

produced when

easily.

 

 

 

 

the vibrations of the speakers

 

 

 

 

 

the volume is

 

 

 

 

 

being conveyed from the floor.

 

 

 

 

 

raised.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Troubleshooting

Remote control

• The batteries are flat.

 

 

• Replace with new batteries.

 

2

 

 

 

 

 

 

 

 

unit does not

• The remote control unit is too far

• Operate from closer to the main

 

2

 

 

 

operate.

away.

 

 

 

 

unit.

 

 

 

 

 

 

• There is an obstacle between the

• Remove the obstacle.

 

2

 

 

 

 

main unit and the remote control

 

 

 

 

 

 

 

unit.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Specifications

 

• The remote control unit is being

• Operate the remote control unit

 

2

 

 

 

 

 

 

 

 

operated at an angle of over 30°

from directly in front of the main

 

 

 

 

 

 

with respect to the front panel.

unit.

 

 

 

 

 

 

• The batteries are inserted in the

• Insert the batteries in the proper

 

2

 

 

 

 

wrong direction.

 

 

direction.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12