![TEST AND ADJUSTMENT](/images/new-backgrounds/44873/448735x1.webp)
TEST AND ADJUSTMENT
❒Turn on the circuit breaker and light switch.
NOTE: Sensor has a 1 1/2 minute warm up period be- fore it will detect motion. When fi rst turned on or when switching modes wait 1 1/2 minutes.
❒Turn the RANGE control to the mid position,
MAX |
|
|
|
|
B | O | ON - TIME | DUAL BRITE | |
| ||||
| O |
|
| |
| T | S |
|
|
MIN |
|
|
| |
| TEST 1 5 2 0 | OFF 3 6 | DUSK TO | |
RANGE |
| |||
| MINUTES | HOUR | DAWN |
Bottom of Sensor
Avoid aiming the sensor at:
•Objects that change temperature rapidly, such as heating vents and air conditioners. These heat sources could cause false triggering.
•Areas where pets or traffic may trigger the control.
•Nearby large,
240°
8ft.
(2.4 m)
70 ft. 100 ft.
(21 m) (30.5 m) Boosted
Maximum Range | Maximum | |
Coverage Angle | ||
|
The detector is less sensitive to motion directly towards it.
MotionMotion
Least Sensitive | Sensor | Most Sensitive |
|
❒ Loosen the clamp screw in the |
|
|
|
| Clamp | |
sensor ball joint and gently |
|
|
|
| Screw | |
rotate the sensor. |
|
|
|
|
| |
❒ Walk through the coverage |
|
|
|
| Ball | |
|
|
|
| |||
area noting where you are |
|
|
|
| ||
|
|
|
| Joint | ||
when the lights turn on. Move |
|
|
|
| ||
|
|
|
|
| ||
the sensor head up, down, or |
|
|
|
|
| |
sideways to change the cover- |
|
|
|
|
| |
age area.Keep the sensor at |
|
|
|
|
| |
least 1" (2.5 cm) away from |
|
| Aim Sensor | |||
the lamps. |
|
| ||||
Down for Short | ||||||
❒ Adjust the RANGE as needed. | ||||||
|
| Coverage | ||||
RANGE set too high may |
|
| ||||
|
|
|
|
| ||
increase false triggering. |
|
|
|
|
| |
❒ Secure the sensor head's |
|
|
|
|
| |
|
|
|
|
| ||
aim by tightening the clamp |
|
|
|
|
| |
screw. Do not overtighten the |
|
| Aim Sensor | |||
screw. | Higher for Long | |||||
❒ Set the amount of TIME you |
|
| Coverage | |||
want the lights to stay on after |
|
|
|
|
|
motion is detected (1, 5, or 20 minutes).
❒Set the
SPECIFICATIONS
Range . . . . . . . . . . . . . . Up to 70 ft. (21 m); 100 ft. (30.5 m) with Range Boost. [varies with surrounding temperature]
Sensing Angle . . . . . . . . Up to 240°
Electrical Load. . . . . . . . Up to 300 Watt Maximum In- candescent [Up to 150 Maxi- mum each lamp holder].
Power Requirements . . . 120 VAC, 60 Hz
Operating Modes . . . . . . TEST, AUTO, and MANUAL MODE
Time Delay . . . . . . . . . . 1, 5, 20 minutes Replacement lamp. . . . . T3, 150W halogen maximum
120 VAC
DESA Specialty Products reserves the right to dis- continue products and to change specifi cations at any time without incurring any obligation to incorporate new features in products previously sold.
3 |