INSTALLATION

Venting Installation (Con.)

Electrical Gookup and Remote Reeiver Diagram

Gas Supply Testing

7

INSTALLATION

Continued

If an offset is necessary in the attic to avoid obstruction, it is important to support the vent pipe every 3 ft. to avoid excessive stress on the elbows and possible separation (see Figure 8, page 7).

Clearances must be maintained between the roof and the ter- mination. Refer to chart below.

Roof Pitch

Minimum Height Above Roof

 

 

Flat - 7/12

1 ft. (30.48 cm)

7/12 - 8/12

1 1/2 ft. (45.72 cm)

8/12 - 9/12

2 ft (60.96 cm)

9/12 - 10/12

2 1/2 ft (76.20 cm)

10/12 - 11/12

4 ft (121.92 cm)

11/12 - 14/12

5 ft (152.40 cm)

14/12 - 16/12

6 ft (182.88 cm)

16/12 - 18/12

7 ft (213.36 cm)

18/12 - 20/12

7 1/2 ft (228.60 cm)

20/12 - 21/12

8 ft (243.84 cm)

 

 

Roof Flashing

Outlet Box

Three-prong Plug

Figure 9 - Duplex Outlet

 

 

TH

 

PI L

 

 

OT

TP

O

 

ON

 

 

T

 

 

L

 

 

I

 

 

P

 

 

OFF

 

TPTH

 

TH

Convertible

TP

 

TPTH

 

Gas Valve

REMOTE

OFF

 

 

ON

 

 

Remote Control

Receiver

Figure 10 - Remote Control Receiver

GAS SUPPLY TESTING

NOTICE: This section is intended as a guide for qualified technicians installing gas to the appliance.

Wall Strap

45° Elbows

Ceiling Firestop

Figure 8 - Vertical Termination with Offset and Wall Strap

ELECTRICAL HOOKUP AND REMOTE RECEIVER DIAGRAM

An outlet box with two receptacles (see Figure 9) has been supplied for your convenience and is located inside on the lower right side of the fireplace.

The remote control receiver is factory wired and connected to the convertible gas valve as shown in Figure 10.

WARNING: Do not connect appliance before pres- sure testing gas piping. Damage to gas valve may result and an unsafe condition may be created.

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).

The appliance must be isolated from the gas supply piping system by closing its individual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

The gas control valve is secured underneath the firebox. Two 1/8" ports are provided on the gas control valve for pressure test gauge connections (see Figure 11).

 

 

Pilot Adjustment

 

To Pilot Burner

 

 

 

 

ON/OFF

 

 

 

ILOT

 

Pilot Gas

Knob

 

 

 

 

Line Do

 

 

 

P

 

 

 

N

 

16AI

 

 

 

 

O

 

 

Not Kink

 

P

 

 

 

 

O

T

 

 

TH

 

 

 

 

7

 

 

I

 

 

 

L

 

 

 

 

 

 

 

L

I

 

To Main

 

 

FFO

O

H

TP

 

 

 

E

A

 

TPTH

Burner

Inlet

 

 

 

 

 

 

 

Flame Adjustment Knob

Pressure

 

 

 

Outlet Pressure

 

 

 

 

 

Figure 11 - Gas Control Valve

 

 

For..com

111916-01C

Page 6 Page 8
Page 7
Image 7
Desa CD32M (-1)(-2) installation manual GAS Supply Testing, Electrical Hookup and Remote Receiver Diagram
Page 6 Page 8

CD32M (-1)(-2) specifications

Desa CD32M (-1)(-2) is a cutting-edge technology designed to meet the demands of modern applications, particularly in the realm of telecommunications and data processing. This sophisticated dual-mode digital system offers versatility and efficiency, making it suitable for various industries including finance, healthcare, and manufacturing.

One of the main features of the Desa CD32M is its advanced processing capability. With a dual-core architecture, it can handle multiple tasks simultaneously, greatly enhancing performance in complex environments. This multi-threading capability allows for improved response times and higher productivity, which is critical for applications that require real-time data analysis and processing.

The Desa CD32M incorporates innovative technologies such as dynamic power management and adaptive processing algorithms. These technologies enable the system to efficiently allocate resources based on task priority, minimizing energy consumption without sacrificing performance. This aspect is particularly important in industries where sustainability and cost-effectiveness are paramount.

Another standout characteristic of the Desa CD32M is its robust security features. With integrated encryption and authentication protocols, it ensures that sensitive information is protected from unauthorized access and cyber threats. This level of security is essential for sectors like finance and healthcare, where data integrity and privacy are critical.

In addition to its hardware capabilities, the Desa CD32M is built for compatibility with a wide range of software platforms. This flexibility allows organizations to integrate the system into their existing workflows seamlessly. Its user-friendly interface also facilitates easier control and monitoring, making it accessible for users with varying levels of technical expertise.

Moreover, the scalability of the Desa CD32M sets it apart from conventional systems. Organizations can expand their operations and upgrade their capabilities without the need for a complete overhaul of their existing infrastructure. This scalability is particularly advantageous in today’s fast-paced business environment, where adaptability is crucial.

Overall, the Desa CD32M (-1)(-2) represents a significant advancement in digital systems technology. Its combination of processing power, energy efficiency, robust security, and scalability makes it an invaluable asset for organizations looking to enhance their operational efficiency while ensuring data protection. As industries continue to evolve, technologies like the Desa CD32M will play an essential role in shaping the future of digital communication and data management.
Top Page Image Contents