INSTALLATION

Removing Glass Panel Installin Log Set

9

INSTALLATION

Continued

REMOVING GLASS PANEL

CAUTION: Before you proceed, make sure your gas control valve is in the OFF position.

1.To remove louvers, pull both spring latches (located in each end of louver) toward center of appliance at the same time until disengaged from locating holes. Repeat for bottom end spring latches (see Figure 16).

2.Remove screen rod by removing rod loop from glass door center bracket. Slide screen rod either to the left or right of fireplace until one end is free to completely remove screen from fireplace.

3.Undo latches located on top and bottom of firebox (see Figure 17). Carefully swing door to the left. The glass door is se- curely mounted to the firebox with 5 screws.

Glass

Locating

Holes

3.Place log #3 (c-shaped crossover log) onto rear and front logs as shown in Figure 20. Make sure it is seated properly on the smooth surface on front log and on the pin on back log.

4.Place log #4 (small round log) on pin on right side of front log (see Figure 21).

5.Place log #5 (small front log) onto the front left part of grate making sure notches fit over prongs of grate (see Figure 22).

6.Place log #6 onto two pins on left side of back and front logs (see Figure 22).

1

2

 

Bottom

LouverSpring

Latch

Figure 16 - Removing Louvers

Open

Close

Figure 17 - Spring Latches

INSTALLING LOG SET

Each log is marked with a number in the following diagram. These numbers will help in identifying the logs when installed. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with fireplace.

Models CD32M and CD36M-A Series

1.Place log #1 (back log) on top of grate as shown in Figure 18. Make sure notches in bottom of log fit over grate.

2.Place log #2 (large front log) over pins on grate (see Figure 19).

Figure 18 - Installing Log #1, Figure 19 - Installing Log #2,

Models CD32M/CD36M-A Models CD32M/CD36M-A Series

Series

3 4

Figure 20 - Installing Log #3,

Figure 21 - Installing Log #4,

Models CD32M/CD36M-A

Models CD32M/CD36M-A

Series

Series

 

6

5

 

Figure 22 - Installing Logs #5 and #6, Models CD32M/CD36M-A Series

For..com

111916-01C

Page 8 Page 10
Page 9
Image 9
Desa CD32M (-1)(-2) installation manual Removing Glass Panel, Installing LOG SET
Page 8 Page 10

CD32M (-1)(-2) specifications

Desa CD32M (-1)(-2) is a cutting-edge technology designed to meet the demands of modern applications, particularly in the realm of telecommunications and data processing. This sophisticated dual-mode digital system offers versatility and efficiency, making it suitable for various industries including finance, healthcare, and manufacturing.

One of the main features of the Desa CD32M is its advanced processing capability. With a dual-core architecture, it can handle multiple tasks simultaneously, greatly enhancing performance in complex environments. This multi-threading capability allows for improved response times and higher productivity, which is critical for applications that require real-time data analysis and processing.

The Desa CD32M incorporates innovative technologies such as dynamic power management and adaptive processing algorithms. These technologies enable the system to efficiently allocate resources based on task priority, minimizing energy consumption without sacrificing performance. This aspect is particularly important in industries where sustainability and cost-effectiveness are paramount.

Another standout characteristic of the Desa CD32M is its robust security features. With integrated encryption and authentication protocols, it ensures that sensitive information is protected from unauthorized access and cyber threats. This level of security is essential for sectors like finance and healthcare, where data integrity and privacy are critical.

In addition to its hardware capabilities, the Desa CD32M is built for compatibility with a wide range of software platforms. This flexibility allows organizations to integrate the system into their existing workflows seamlessly. Its user-friendly interface also facilitates easier control and monitoring, making it accessible for users with varying levels of technical expertise.

Moreover, the scalability of the Desa CD32M sets it apart from conventional systems. Organizations can expand their operations and upgrade their capabilities without the need for a complete overhaul of their existing infrastructure. This scalability is particularly advantageous in today’s fast-paced business environment, where adaptability is crucial.

Overall, the Desa CD32M (-1)(-2) represents a significant advancement in digital systems technology. Its combination of processing power, energy efficiency, robust security, and scalability makes it an invaluable asset for organizations looking to enhance their operational efficiency while ensuring data protection. As industries continue to evolve, technologies like the Desa CD32M will play an essential role in shaping the future of digital communication and data management.
Top Page Image Contents