INSTALLATION

Continued

INSTALLATION ITEMS

Before installing fireplace, make sure you have the items listed below.

external regulator (supplied by installer, for propane/LP units only)

piping (check local codes)

sealant (resistant to propane/LP gas)

equipment shutoff valve *

test gauge connection*

ground joint union

sediment trap

tee joint

pipe wrench

*A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 44.

Note: If desired, purchase a four-sided brass trim kit for built-in installations. See Accessories, page 44.

FIREPLACE CLEARANCES

WARNING: Maintain the minimum clearances shown in Figure 7. If you can, provide greater clearances from floor, ceiling, and joining wall.

If your fireplace is to be used with an optional mantel, the installation instructions included with your mantel shows an CSA approved method of attaching the fireplace/mantel system to a wall. IMPORTANT: Only use optional cabinet or corner mantels specified in this manual. Purchase the optional mantel from your dealer (see Acces- sories, page 44).

If your fireplace is to be recessed into the wall, see Built-In Fireplace Installation to secure your fireplace into the wall.

CAUTION: If you install the fireplace in a home garage

fireplace pilot and burner must be at least 18 inches above floor.

locate fireplace where moving vehicle will not hit it.

For convenience and efficiency, install fireplace

where there is easy access for operation, inspec- tion, and service

in coldest part of room

An optional blower kit is available from your dealer. See Accessories, page 44. If planning to use blower, follow instructions provided with blower for power source.

Minimum Clearances For Side

Combustible Material, Side Wall, and

Ceiling

A.Clearances from the side of the fireplace cabinet to any combustible material and wall should follow diagram in Figure 7.

Example: The face of a mantel, bookshelf, etc. is made of combustible material and protrudes 3 1/2" from the wall. This combus- tible material must be 4" from the side of the fireplace opening (see Figure 7).

B.Clearances from the top of the fireplace opening to the ceiling should not be less than 36 inches.

C.For mantel clearances, see Figure 11, page 12.

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS

Top

Left and

Bottom

 

Right Sides

and Rear

36"

6"

0"

 

Example

 

 

 

*

*Minimum 16 inches from Side Wall

Figure 7 - Minimum Clearance for

Combustible to Wall

BUILT-IN FIREPLACE

INSTALLATION

Built-in installation of this fireplace involves installing fireplace into a framed-in enclosure. This makes the front of fireplace flush with wall. An optional brass trim kit accessory is available (see Accessories, page 44). Brass trim will extend past sides of fireplace approximately 1/2" . This will cover the rough edges of the wall opening. If installing a built-in mantel above the fireplace, you must follow the clearances shown in Figure 12, page 12. Follow the instructions below to install the fireplace in this manner.

10

www.desatech.com

111244-01F

Page 10
Image 10
Desa CDCFPR, CDCFTNA, CDCFTPA Installation Items, Fireplace Clearances, Minimum Clearance to Combustible Materials, Top

CDCFTNA, CDCFPR, CDCFTPA specifications

Desa CDCFTPA, CDCFPR, and CDCFTNA represent a suite of advanced technologies and methodologies employed in the development and management of efficient distribution networks within the field of telecommunications and data services. These frameworks are designed to enhance connectivity, streamline processes, and ensure optimal performance in various environments.

One main feature of Desa CDCFTPA (Coaxial Digital Channel Fiber Transmission Protocol Architecture) is its ability to integrate coaxial cables with fiber optic technology, enabling high-speed data transmission over existing infrastructures. This hybrid approach not only reduces the need for extensive renovations but also capitalizes on the advantages of both technologies, offering broadband accessibility and improved bandwidth capabilities. By leveraging both mediums, operators can deliver enhanced services while maintaining cost-efficiency.

CDCFPR (Centralized Data Control Fiber Processing Resource) represents a centralized approach to managing data flow within telecommunications networks. Its core characteristic lies in its architecture, which supports dynamic allocation of resources in real-time. This enables network operators to efficiently allocate bandwidth based on demand, optimize routing paths, and reduce latency. Additionally, CDCFPR employs advanced algorithms for data compression and encryption, ensuring that users experience a seamless and secure connection.

CDCFTNA (Carrier Digital Channel Fiber Transmission Network Architecture) is focused on creating robust networks that can support a variety of distribution channels, including 5G and IoT devices. Its design emphasizes scalability and adaptability, allowing network providers to easily expand or modify their infrastructure to meet evolving market needs. Key technologies incorporated in CDCFTNA include Software-Defined Networking (SDN) and Network Function Virtualization (NFV), which enable operators to manage their resources more flexibly and efficiently.

Each of these frameworks boasts unique characteristics that contribute to the overall enhancement of telecommunications systems. They embody a commitment to innovation, sustainability, and user-centric design, aligning with current trends in digital services and communication technologies. By deploying such advanced systems, service providers can ensure they remain competitive in a fast-paced and continuously evolving market. In summary, Desa CDCFTPA, CDCFPR, and CDCFTNA collectively represent the future of telecommunications infrastructure, promising improved connectivity, efficiency, and adaptability for a diverse range of applications.