Desa LGCFTN, LGCFTP installation manual Can cause improper and danger, Installing Blower Assembly

Models: LGCFTN LGCFTP

1 32
Download 32 pages 10 Kb
Page 13
Image 13

 

INSTALLation

6. Route the wire harness through the hole in

 

Continued

left side of baffle. Pull wire harness through

 

 

 

lower opening above where the valve shield

 

 

Branch

was removed. (see Figure 16).

Shoulder Screw

Support

7. Insert the 4 wire harness into one of the round

 

 

 

holes in the rear of the valve cover shield and

 

Valve

 

through the rectangular hole in the front of

Remove

Cover

 

shield (see Figure 16).

Shield

 

8. Reconnect red wire to switch position 3.

Screw

 

 

Reconnect blue wire to switch position 1.

 

 

 

Reconnect green and white wires.

 

 

 

9. Install the switch plate on the valve cover shield

 

 

 

with 2 #10 screws provided (see Figure 17).

 

 

 

Reinstall the valve cover shield. Route power

 

 

 

cord out of the cabinet by inserting it through the

 

 

 

bushing on the outer casing (see Figure 16). Plug

 

 

Bottom Louver

fan kit into 120-Volt grounded power supply and

Snap Bushings

Assembly

test operation. Note: When switch is in theAUTO

Figure 15 - Removing Valve Cover Shield

position, the fan will start after the heater has run

for a few moments. The fan will continue to run for

Installing Blower Assembly

several moments after the heater has been turned

 

 

 

off. When switch is in the ON position, the fan

CAUTION: Label all wires

will run until turned to OFF. Reinstall upper louver

assembly and hood if previously removed, (see

prior

to disconnection when

Figure 14, page 12). Close lower louver door.

servicing controls. Wiring errors

Blower Bracket

 

can cause improper and danger-

Wire Harness

ous operation.

 

Assembly

Wiring Routing

 

 

 

 

 

Screw

Hole in Baffle

CAUTION: Verify proper op- eration after servicing.

Baffle

Note: If you are using a mantel with your heater, use the following instructions. If your heater is built-in, see For Built-In Installation on page 14.

1.Install snap bushings found in hardware kit into both holes in rear of valve cover shield.

2.Make sure the wire harness is firmly connected to the terminals on the blower bracket assembly.

3.Note the wire locations on back of AUTO/ OFF/ON switch. The terminals on back of switch are numbered 1, 2 and 3. Carefully remove red wire from terminal 1 and blue wire from terminal 3. Black wire can remain on middle terminal 2 (see Figure 16).

4.Carefully disconnect green and white wires at their insulated connectors.

5.In top of the heater cabinet, locate the four mounting holes on the outer casing. Align these four holes with those on the blower bracket assembly. Attach blower bracket as- sembly to the outer casing with 4 #10 screws provided (see Figure 16).

Switch Power

Cord

Red

Switch

Plate

Blue

Wire

Valve Cover Shield BoxCover Harness

Figure 16 - Installing Blower Bracket

Assembly

Valve

Cover

Shield

Switch Plate

Screw

Figure 17 - Installing Switch Plate to

Valve Cover Shield

119508-01A

www.desatech.com

13

Page 13
Image 13
Desa LGCFTN, LGCFTP installation manual Can cause improper and danger, Installing Blower Assembly

LGCFTN, LGCFTP specifications

Desa LGCFTP and LGCFTN are innovative technology solutions designed to cater to modern communication and data management needs. These platforms are part of a broader suite of services aimed at enhancing connectivity, streamlining data flow, and enabling seamless interaction between users and systems.

One of the main features of Desa LGCFTP is its robust file transfer capabilities. It utilizes the File Transfer Protocol (FTP) to ensure that data can be moved securely and efficiently over networks. This feature is particularly crucial for businesses that handle large amounts of data, as it allows for the quick transfer of files ranging from reports to multimedia content without compromising on security.

In addition to the FTP functionalities, Desa LGCFTN incorporates advanced networking technologies that enhance connectivity among users. This platform is designed to facilitate reliable connectivity options, enabling organizations to establish networks that can support various applications, from simple database queries to complex real-time data exchanges.

Both Desa LGCFTP and LGCFTN are built with scalability in mind. This means that as user requirements grow, these systems can easily adapt to accommodate increased data loads and more extensive user bases. The technology underpinning these platforms is based on an architecture that supports distributed processing, which is essential for ensuring that performance remains high, even as demand fluctuates.

Security is a top priority for both platforms. They implement a range of protocols and encryption techniques to safeguard data during transfers and while at rest. This commitment to security helps organizations maintain compliance with industry standards and regulations, which is increasingly important in today’s data-driven environment.

Desa LGCFTP and LGCFTN also emphasize user experience. Their intuitive interfaces make it easy for users to manage files and navigate through different features. This focus on usability reduces the learning curve, ensuring that teams can quickly leverage the full capabilities of the platforms without extensive training.

In summary, Desa LGCFTP and LGCFTN represent cutting-edge solutions in the realm of file transfer and network connectivity. With their emphasis on security, scalability, and user experience, these platforms are well-equipped to meet the challenges faced by modern businesses, making them invaluable tools for efficient data management and communication.