Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug the charger before attempting to clean.
•DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together.
•These chargers are not intended for any uses other than charging DEWALT rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.
•Do not expose the charger to rain or snow.
•Pull by the plug rather than the cord when disconnecting the charger. This will reduce the risk of damage to the electric plug and cord.
•Make sure that the cord is located so that it will not be stepped on, tripped over or otherwise subjected to damage or stress.
•Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock or electrocution.
•When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
•An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is, 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavier the cord.
5
|
| Minimum Gauge for Cord Sets |
|
|
| |||
|
| Volts | Total Length of Cord in Feet (meters) |
|
| |||
Ampere Rating | 120 V | 25 (7.6) | 50 (15.2) | 100 (30.5) | 150 (45.7) |
|
| |
|
| 240 V | 50 (15.2) | 100 (30.5) | 200 (61.0) | 300 (91.4) |
| English |
More | Not |
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
Than | More |
|
| AWG |
|
|
|
|
| Than |
|
|
|
|
|
|
|
0 | 6 |
| 18 | 16 | 16 | 14 |
|
|
6 | 10 |
| 18 | 16 | 14 | 12 |
|
|
10 | 12 |
| 16 | 16 | 14 | 12 |
|
|
12 | 16 |
| 14 | 12 | Not Recommended |
|
| |
|
|
|
|
|
|
|
|
|
•Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.
•Do not operate the charger with a damaged cord or plug.
•Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take it to an authorized service center.
•Do not disassemble the charger; take it to an authorized service center when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
•Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
•NEVER attempt to connect 2 chargers together.
•The charger is designed to operate on standard 120 V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.
