FIG. 8

Guards and Flanges

It is important to choose the correct guards and flanges to use with the grinder accessories. See page 5051 and this page for the correct accessories.

NOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose.

To turn the tool on, push the lock-off lever (I) toward the back of the tool, then depress the paddle switch (G). The tool will run while the switch is depressed. Turn the tool off by releasing the paddle switch.

FIG. 6

G

I

English

WARNING: Accessories must be rated for at least the speed recom- mended on the tool warning label. Wheels and other accessories running over rated accessory speed may burst and cause injury. Every unthreaded accessory must have a 7/8" arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 50–51. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

Switches

CAUTION: Hold the side handle and body of the tool firmly to maintain control of the tool at start up and during use and until the wheel or accessory stops rotating. Make sure the wheel has come to a complete stop before laying the tool down.

NOTE: To reduce unexpected tool movement, do not switch the tool on or off while under load conditions. Allow the grinder to run up to full speed before touching the work surface. Lift the tool from the surface before turning the tool off. Allow the tool to stop rotating before putting it down.

PADDLE SWITCH (DWE4120) (FIG. 6)

CAUTION: Before connecting the tool to a power source depress and release the paddle switch (G) to ensure that the switch is off.. Depress and release the paddle switch as described above after any interruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure.

52

WARNING: Do not disable the lock-off lever. If the lock-off lever is disabled, the tool may start unexpectedly when it is laid down.

LOCK-ON BUTTON (DWE4120) (FIG. 7)

The lock-on button (H) offers increased comfort in extended use

applications. To lock the tool on, push the

 

 

 

 

 

 

FIG. 7

 

 

 

lock-off lever (I) toward the back of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

tool then depress the paddle switch (G).

 

 

 

 

 

 

 

With the tool running, depress the lock-

 

 

 

 

 

 

 

on button (H). The tool will continue to

 

 

 

 

 

 

 

run after the paddle switch is released. To

 

 

 

 

 

 

 

 

 

 

 

 

 

H

 

 

 

 

I

 

unlock the tool, depress and release the

 

G

 

 

 

 

 

 

 

 

paddle switch. This will cause the tool to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

stop.

 

 

 

 

 

 

 

CAUTION: Allow the tool to reach full speed before touching tool to the work surface. Lift the tool from the work surface before turning the tool off.

SPINDLE LOCK (FIG. 8)

A

The spindle lock button (A) is provided to prevent the spindle from rotating when installing or removing wheels. Operate the spindle lock only when the tool is turned off, unplugged from the power supply, and has

come to a complete stop. Do not engage the spindle lock button while the tool is operating because damage to the tool will result. To engage the lock, depress the spindle lock button and rotate the spindle until you are unable to rotate the spindle further.

Page 54
Image 54
DeWalt DWE4120N Guards and Flanges, Switches, Paddle Switch DWE4120 FIG LOCK-ON Button DWE4120 FIG, Spindle Lock FIG