Dimplex CAL100, CAL150, CAL075, CAL200 dimensions Electrical, General, Wall Mounting / Installation

Installation and Operating Instructions

Calidou Electronic Panel Radiator

Models:									IP24	Issue 5 November 2004
CAL075 / CAL100 / CAL150 / CAL200
Dimensions and Specification
Model	Loading	Length (A)	Height	Depth	X	Y	Z	Weight
	(kW)	(mm)	(mm)	(mm)	(mm)	(mm)	(mm)	(kg)
CAL075	0.75	455	604	142	140	87	228	17
CAL100	1.0	621	604	142	300	87	234	24
CAL150	1.5	870	604	142	400	226	242	33
CAL200	2.0	1202	604	142	700	227	275	47

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

IMPORTANT SAFETY ADVICE

•When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following:

•WARNING THE SURFACES OF THIS HEATER CAN BE HOT Momentary contact with any part of the heater should not cause injury. However, aged or infirm persons or young children should not be left unsupervised in the vicinity of the heater unless a suitable guard is fitted

•IMPORTANT – If this heater is installed in a room containing a bath or shower, it should be so installed that switches and other controls cannot be touched by a person using a bath or shower – to comply with this requirement see ‘Lock the Control Cover’ section on page 2.

•If you use this heater in conjunction with an external thermal control, a programme controller, a timer or any other device which switches the heat on automatically, observe all safety warnings AT ALL TIMES since a fire risk exists when the heater is accidentally covered or displaced

•The installation of this product should be carried out by an electrician or competent person and be in strict accordance with the current IEE Wiring Regulations and relevant Building Regulations

•This heater must not be mounted within 150mm of curtains and other combustible materials or 100mm from a shelf or overhang

•NEVER cover or obstruct in any way the heat outlet slots at the top of the heater or the air inlet slots at the base of the heater

•DO NOT cover the heater – Do not place material or garments on the heater or obstruct the air circulation around the heater

•Before connecting the heater check that the supply voltage is the same as that stated on the heater

•The heater must be installed in accordance with these instructions

•The heater must be mounted using the wall bracket supplied. The heater should only be operated in the upright position

•The heater should be positioned in accordance to the clearances stated in these instructions

•DO NOT locate this heater immediately beneath a fixed socket outlet

Electrical

The wires in the mains lead are coloured in accordance with the following code:

GREEN & YELLOW	EARTH
BLUE	NEUTRAL
BROWN	LIVE
BLACK	PILOT WIRE

General

The Calidou radiator is designed to provide exceptional levels of comfort with a combination of radiant and convected heat in both domestic and commercial applications.

Wall Mounting / Installation

The heater should be positioned observing the minimum clearances stated around the heater.

(see also ‘Electrical’ section)

The wall bracket supplied with the heater must be used

1.Using a screwdriver, turn the latch in a clockwise direction to unlatch the bracket, then remove it from the appliance (see Fig.1)

2.Mount the bracket on the wall using a minimum of 4 screws

(max diameter 6mm) making sure that it is the correct way up and at the correct height. (see Fig.2)

3.Position the appliance on the bracket.

4.Re-latch the bracket turning the latch anti-clockwise.

Fig.1

		Fig. 2
Model	A (mm	B (mm)
CAL075	140	228
CAL100	300	234
CAL150	400	242
CAL200	700	27

If the wall is a light partition or crumbling, then supporting legs are also needed

(Part No. CAL0001). The heater MUST be fitted to the wall as well as having the supporting legs

(See also ‘Pilot Wire Connection’)

The heater is fitted with a length of flexible cable for connection to the fixed wiring of the premises through a suitable connection box positioned adjacent to the heater.

The supply circuit to each heater must incorporate a double pole isolating switch having a contact separation of at least 3mm

Pilot Wire Connection

The BLACK control wire is designed to carry a signal from slot in or wall mounted Dimplex programmers. If, however a programmer is not being used, the pilot wire should be isolated in accordance with the current IEE Wiring Regulations.

IMPORTANT - Do NOT connect the BLACK pilot wire to earth

Care should be taken with the installation of the pilot wire(s) as when switching to background (set back) they become energised at 240V although only at a current of 1mA.

In every case a suitable means of isolation must be provided for the pilot wire and marked to indicate that two sources of supply may be present at the heater.

Where pilot wires are installed separately from the heater final sub-circuit they should be protected, double insulated and carry their own integral earth continuity conductor.

1.Place the legs under the heater

2.Position the hinges into the grooves in the air inlet

3.Unscrew the jacks, until they reach the floor