DKS Enterprises 1814 AND

2.2.2 Controlling a Gate Operator and Pedestrian Gate (or Door)

When controlling a gate operator and pedestrian gate (or door), relay 1 is typically used to control the

gate operator while relay 2 is typically used to control the door or gate. Note that the electric strike

and the magnetic lock are powered from their own power supply. The relay 2 contact is set to either

normally open (NO) for electric strikes, or normally closed (NC) for magnetic locks by placing the

relay 2 contact shorting bar on either the NO or NC pins.

A variation of this diagram is for the system to control two doors or two gates.

13 14 15 16 17

Relay 2 COM

Relay 2

Relay 1 COM

Relay 1 NO

Relay 1 NC

AND

Gate Operator

Electric Strike

Magnetic Lock

Contents

Main Owners Manual Page Use this manual with the following models only. TABLE OF CONTENTS Preface Section 1 Installation Section 2 Wiring Section 3 Programming Section 4 Adjustments Section 5 Operating Instructions Section 6 Maintenance and Trouble Shooting IMPORTANT NOTICE FCC - UNITED STATES DOC - CANADA Notice: Notice: Page Page SECTION 1 - INSTALLATION 1.1.1 Surface Mount Units 1.1.2 Surface Mount Units with Recess Box 1.1.3 Flush Mount Units 1.1.4 Flush Mount Rough-in Box 1.1.5 Flush Mount Trim Ring 1.1.6 Flush Mount Surface Mounting Kit 1.1.7 Wall Mount Units Page Page SECTION 2 WIRING Page Page 2.2.1 Controlling a Single Door or Gate Gate Operator Electric Strike Magnetic Lock 2.2.2 Controlling a Gate Operator and Pedestrian Gate (or Door) AND Gate Operator Electric Strike Magnetic Lock Page SECTION 3 PROGRAMMING 3.1.1 Programming from the Keypad 3.1.2 Programming with an IBM Keyboard 3.1.3 Programming with a Touch-Tone Telephone 3.2.1 Master Code 3.2.2 Single or Multiple Systems 3.2.3 Programming for Call-up Operation 3.2.4 Relay Strike Time 3.2.5 Talk Time 3.2.6 Tone Open Numbers 3.2.7 Postal Switch 3.2.8 Touch-tone / Rotary-dial 3.2.9 Rotary-dial 9 3.3.1 Programming Letters and Numbers MNO 3.3.2 Programming the User Message 3.3.3 Programming the Instruction Message Page 3.4.1 Programming the Directory Code Length 3.4.2 Programming 7-digit Phone Numbers 3.4.3 Programming Area Codes 3.4.4 Programming Phone Numbers with Area Code Reference 3.4.5 Programming Names 3.4.6 Deleting Individual Phone Numbers 3.4.7 Delete Names 3.4.8 Delete Area Codes 3.4.9 Display Phone Numbers 3.5.1 Programming Four-digit Entry Codes 3.5.2 Delete Four-digit Entry Codes 3.5.3 View Four-digit Entry Codes 3.5.4 Entry Code Divide Number Page SECTION 4 ADJUSTMENTS 4.1 Speaker Volume 4.2 Feedback 4.3 Click Sensitivity 4.4 Display Contrast 4.6 Ring Pin 4.7 Relay 2 Contact Pin 4.8 Auto 1816 Pin 4.9 HF HS Pin 1814 Adjustment Locations Page SECTION 5 OPERATING INSTRUCTIONS 5.2.1 Responding to a Guest Call 5.2.2 Using an Entry Code 5.3.1 Opening from a Remote Location 5.3.2 Hold-Open Command 5.3.3 Relay Check 5.4.1 Talk Time 5.4.2 Line Sharing 5.4.3 Connection to a PBX 5.4.4 Areas with 10-digit Dialing Page SECTION 6 MAINTENANCE SYMPTON POSSIBLE SOLUTION(S) SYMPTON POSSIBLE SOLUTION(S) Page Page Page Page Page Resident Instruction Sheet Guest Communication Granting or Denying Access Call Waiting Privacy