Dolby Laboratories DP503 3.4 Configuring Jumper Settings

3-3

3.4 Configuring Jumper Settings

The Model DP503 includes certain user-selectable options that are configured by

means of internal jumpers, as shown below. Their default settings (shipped with

the unit) are shown in the figure. Any jumpers not specifically mentioned are for

factory use only and should not be disturbed.

Removing the Top Cover

If you need to gain access to the interior of the DP503 to change these jumpers,

remove the top cover of the unit as follows:

WARNING: Be sure that the unit is NOT powered up. As there is no power switch, the power cord must

not be connected.

Using the supplied hex wrench, remove the 12 screws securing the top

cover to the chassis; there are three screws on the upper front panel, upper

rear panel, and each of the sides. The three washerless screws should be

reserved for affixing at the top of the front panel when re-assembling the

unit.

Note: The front panel is attached to the chassis by means of 3 screws at the lower portion of the

front panel. These do not need to be disturbed in order to remove the top cover.

Gently lift the top cover upward and towards the rear. Carefully set aside.

Reverse the above procedure when re-assembling the unit.

Signal ground to

chassis ground link ST input clock

termination (150 ohm)

TERMINATED

NOT TERMINATED

600

10K

600

10K

J13 J14

J14 J12

LINKED

OPEN

Audio input

termination

DP503 MOTHERBOARD

S101

ChB ChA

MAIN

Contents

Main Page Users' Manual For Model DP503 Page TABLE OF CONTENTS Page Page Page SECTION 1 INTRODUCTION 1.1 Introduction 1.2 Features 1.3 Dolby AC-2 and Dolby Digital (AC-3) Page 1.5 Regulatory Notices FCC UL UK 1-5 IEC NOTICES GB F D I Page SECTION 2 APPLICATIONS 2.1 Telecommunications Dolby Fax 2.2 Cable 2.3 Satellite / Terrestrial Radio Communications SECTION 2A DOLBY FAX - AN OVERVIEW 2A.1 Introduction 2A.2 Algorithms and Applications ISDN 2A.3 Quick Start for Equipment Installation 2A.4 Quick Start for ISDN Setup 2A.5 Quick Start for Developing a Phone Directory 2A.6 Quick Start for Placing Dolby Fax Calls 2A.7 Receiving Dolby Fax Calls 2A-5 2A.8 Some Specific Applications ISDN Location X Location Y Stereo Playback Soundtrack Approval 2A-7 ISDN Location X Location Y Dubbing Sound to Picture Multi-track Recording SECTION 3 PRE-INSTALLATION 3.1 Unpacking 3.2 Inspection 3.2.2 Claims for Shipping Damage 3.3 Fusing Information Main Fuse: Internal Fuse 3.4 Configuring Jumper Settings Removing the Top Cover 3.4.1 Clock Termination Jumper J12 3.4.2 Analog Audio Input Termination J13/J14 3.4.3 Signal Ground-to-Chassis Link J15 3.5 Configuring the Rear Panel DIP Switch S101 3-5 3.5.1 Switch nos. 1-5 - Unit Address Note The address is set using conventional binary codes as follows: 3.5.2 Switch no. 6 - Mode of Operation: Normal/Download 3.5.5 Switch nos. 7 & 8 - Baud Rate Set SECTION 4 INSTALLATION AND LEVEL CALIBRATION 4.1 Mounting 4.2 Audio Connections 4.2.1 S/PDIF Input 4.2.2 AES/EBU Input 4.2.3 Analog Input 4.3 Data / Status / Control Connections 4.3.1 Encoded Data Out and Timing 4.3.2 Auxiliary Data 4.3.3 Terminal Adapter Control 4.3.4 Remote Control 4.4 Power 4.5 Level Calibration (Analog Inputs) Calibration Procedure 4.6 Dolby Fax ConnectionsAdditional Procedures 4.6.1 Mounting 4.6.2 Audio Connections 4.6.3 Encoded Data Out and Timing Page 4.6.10 ISDN Connections SECTION 5 OPERATION 5.1 Introduction to the User Interface 5.1.1 Push-button Key Description Page 5.1.2 Operational Modes 5.1.3 Operational Hierarchy 5.2 Encoder Configuration 5.2.1 To change Algorithm Type 5.2.2 To change Data Rate 5.2.3 To change Channel Mode 5.2.4 To change Sample Rate 5.2.5 To change Aux Rate (auxiliary data rate) 5.3 ISDN Setup only ) 5.3.1 Entering ISDN Setup Mode 5.3.2 To choose Switch Type 5.3.3 To configure Line 1 (L1) ENABLE L1? Y N PRI NUM1: _ PRI SPID1: _ SEC NUM1: _ SEC SPID1: _ 5.3.4 To configure Line 2 (L2), Line 3 (L3), Line 4 (L4) 5.3.5 Concluding ISDN Setup UPDATE TA? Y N UPDATING TA... 5.4 Using the DIRectory: Dolby Fax Applications 5.4.1 Entering DIRectory Mode 5.4.2 Creating New Directory Entries NAME: _ PHONE: _ EDIT CODEC? Y N EDIT ISDN? Y N BONDING-1 64 STORE ENTRY? Y N RE-EDIT? Y N 5.4.2.1 Using the COPY ENTRY? Feature INITIALIZING TA YOUR ENTRY 1 5.4.4 Editing Directory Entries 5.4.5 Deleting Directory Entries 5.5 Using the DIRectory: Encoder-only Applications AC2 256 2C 48 12 5.5.1 Entering DIRectory Mode 5.5.2 Creating New Directory Entries NAME: _ EDIT CODEC? Y N STORE ENTRY? Y N RE-EDIT? Y N 5.5.2.1 Using the COPY ENTRY? Feature 5.5.3 Using Directory Entries 5.5.4 Editing Directory Entries 5.5.5 Deleting Directory Entries Page Page Page APPENDIX A INTERFACE SPECIFICATIONS AND DESCRIPTIONS A.1 DP503 Connector Pinouts A.1.1 Analog Audio Input, J101 & J102 A.1.2 AES/EBU Digital Audio Input, J103 A.1.3 S/PDIF Digital Audio Input, J104 A-2 A.1.4 Encoded Data Out and Timing, J105 DB-37 male connector. A.1.5 Aux/Acc RS-232 Port, J106 DB-9 female connector. A-3 A.1.6 TA Ctrl RS-232 Port, J107 DB-9 male connector. A.1.7 Rem/Download RS-232 Port, J108 DB-9 female connector. A.1.8 Status, J109 A.2 RS-449 Interface Description A.2.1 Functional Description A.2.2 Interface Timing A.2.3 Back-to-Back Testing A.2.4 Dolby Fax Cable Pinout, Part No. 83293 Page APPENDIX B SOFTWARE DOWNLOADING PROCEDURE B.1 Introduction B.2 Software Downloading Procedure DP503 INIT XX.X READY TO LOAD... SERLOAD COM# BAUD FILENAME UPDATE COMPLETE Page Page APPENDIX C DP503 USER INTERFACE STRUCTURE C.1 Setup Menu Operation C-2 C.2 Directory Menu Operation - USE C-3 C.3 Directory Menu Operation - EDIT C-4 C.4 Directory Menu Operation - NEW C-5 C.5 Directory Menu Operation - DEL Page APPENDIX D ISDN ORDERING GUIDE (NORTH AMERICA) D.1 Introduction D.2 Ordering ISDN Service D.2.1 Switch Types D.2.2 B Channels D.3 Regional Bell Operating Companies ISDN Hotlines APPENDIX E GLOSSARY OF ISDN TERMS