Dolphin Peripherals DX5B Charger positioning, Electrical requirements, Caddy Assembly, Handle

Minimum 10 ft. (3 m.)

1 2 3 4

1

4

2

3

Fig

A

Fig

B

Fig

C

AFig

C 1

D

Fig

BC C 2

Read carefully before using your DOLPHIN dx 5 Battery Robot Pool Cleaner 1 ) S a f e t y

1.1 Charger positioning:

The Caddy and Charger [1 page-10]should be positioned at a minimum distance of 10 Ft. (3 m.) from the edge of the pool.

Caution: The Charger should be placed in the shade.

1.2) Electrical requirements:

Factory-wired for either 100V, 115V or 230V mains supply, the voltage rating should be checked before connection. Ensure that the mains/line outlet is protected by a ground fault interrupter (GFI) or earth leakage interrupter (ELI).

Use only the original DOLPHIN Charger.

Warning! DO NOT ENTER THE SWIMMING POOL WHILE THE DOLPHIN IS IN OPERATION.

2 ) D O L P H I N S e t - U p

2.1) Caddy Assembly

Please follow these instructions and refer to the attached diagram when assembling your Caddy.

[Fig. O, page-9].

•Connect the wheel assembly [c-1page-9]by firmly inserting it into the groove at the bottom of the base. Ensure that it is centered, with a washer [c-2page-9]on each side.

•Remove the two locking plates at the bottom of the base to lock the wheel assembly in place.

•Connect the two straight pipes [c-3page-9]onto the bottom of the handle with the horns [c-4page-9]. They should "click" into position.

Note: There are 2 small holes at each end of both pipes. The holes, which are located at a longer distance from the edge of the pipe, must be inserted into the handle.

•Insert the assembled straight pipes and handle into the apertures in the tower until they both "click" and lock into position at the base of the tower [c-5page-9].

•Fasten the plastic charger [c-6page-9]to the Caddy tower by fitting the slots in the back of the Charger's handle over the "T" pins in the tower. Press down firmly until the base of the Charger fits onto the tower base.

•Clip the pike holder [c-7page-9]onto the Caddy.

•Clip the pike [c-8page-9]onto the Caddy straight pipe with black base to create a pike pole.

•Attach the assembled pike pole onto the pike holder and onto the pike base.

•Clip the Caddy float holder [c-9page-9]onto the Caddy.

•Place DOLPHIN on the Caddy.

•Place float [2 page-10]in the float holder.

Important: Ensure that the float switch is in an OFF position.

• Connect the enclosed charging cable [3 page-10]to the Charger.

2.2) Handle

The DOLPHIN features an adjustable handle [4 page-10]that is fitted into slots on each side of the DOLPHIN body.

After the unpacking of the DOLPHIN from its carton box, the handle must be locked in a diagonal position across the top of the DOLPHIN body in order to ensure optimum cleaning results.

Press downwards on each latch [5 page-10]to move independently each handle arm [Fig B].

The two latches feature two round slots [6 page-10] [Fig C], which enable the setting of the handle arm at different positions with varying angles. The normal angle positions of the handle [Fig C-1]will provide the fastest possible waterline sideways movement.

The positions in Fig C-2will provide the slowest waterline sideways movement.

2.3) Remote Control Unit (R.C.U.)

Remote Control Unit requires two 1.5 V AAA batteries (included). The R.C.U. is splash-proof only. Keep it away from direct sunlight or rain.

This R.C.U. is equipped with a digital screen, soft touch buttons and a Joystick for manual operation.

2