➃ Select Optional Accessories, Yes No | Draper SL9, SL5, SL10, SL4

Scissor Lift Submittal & Planning Sheet for SL and SLX Series page 2 of 4

➃Select Optional Accessories

Optional Ceiling Access Door (2 x 2) to allow access above ﬁnished ceiling (highly recommended)

White Painted Finish

Accepts Ceiling Tile

Optional SMS Low Proﬁle Mount and Universal Bracket

A) If you selected the SMS Low Proﬁle Mount please provide the following Projector information (supplied by others)

ManufacturerMake/ModelProjector Size H x W x L: Optional plenum housing: optional ceiling closure panel not included.

B) If you selected the plenum housing option please provide the following information:

Projector Size H x W x L:		Bracket height:		Available space above ceiling:
Optional ceiling closure panel.

Optional ceiling ﬁnish kit: consists of ceiling closure panel and mating trim kit to ﬁnish ceiling opening.

C)If you selected one of the above options please use the following chart to select the correct size plenum housing, ceiling closure, or ceiling ﬁnish kit:

	Size B	Size S	Size E	Size J	Size G	Size U
	(SL Only)	(SL Only)
Max. Projector Size W x L	25" x 25"	25½" x 27½"	25½" x 35½"	25½" x 39½"	31½" x 44½"	27½" x 30½"
Ceiling Opening W x L	297/8" x 297/8"	29½" x 32"	29½" x 40"	29½" x 44"	357/8" x 49"	367/8" x 367/8"	(Trim edge–to–edge)
Ceiling Closure Panel W x L	305/16" x 305/16"	30" x 32½"	30" x 405/8"	30" x 44½"	363/8" x 49½"	373/8" x 373/8"	(Trim edge–to–edge)

➄ Do you want the optional factory installed hookup for RGB, Video and Projector Control?

Yes No

A What type of connectors do you need on Inputs (to Projector)?		What type of connectors do you need on Outputs (to Lift)?
BNC	How Many?	BNC	How Many?
15 Pin HD	How Many?	15 Pin HD	How Many?
RCA	How Many?	RCA	How Many?
S-Video	How Many?	S-Video	How Many?
RS232 (DB9)	How Many?	RS232 (DB9)	How Many?

➅Select Voltage:

110-120V

220-230V

➆Select Controls: This unit comes with one 12v Toggle Switch and 12v Momentary Key Control. For other switching

options, please select from below:

Optional Video Interface Control (VIC12) for projection screen operation

Optional Key Operated Power Supply Key Switch (On-off)
Optional Low Voltage Control (LVC-III)—24V*
Specify number of switches (LVC-S)			(Controls the "Show" position only)
*This is required for any of the following options:

Wireless Remote Control (radio frequency transmitter & receiver) (Controls the "Show" position only)

Wireless Remote Control (infrared transmitter & receiver) (Controls the "Show" position only)

➇Will this unit be controlled by other equipment?

No.

Yes. What kind of equipment?

Speciﬁcations—Scissor Lift

video projector lifts, Model (SL4/SL5/SL6/SL7/SL8/SL9/SL10/SLX11/ SLX12/SLX13/SLX14/SLX15/SLX16/SLX17), for projectors weighing up to 350#. Dove grey baked powder coat ﬁnish. Projector bolts onto operating pan, or mounts to pan with optional SMS Low Proﬁle Lift Bracket (projectors through 26 lbs only). Electrically operated 110-120V AC, 60 Hz. UL recognized gearmotor, with metal chain drive system, to be lifetime lubricated.

For SL Models: Projector to be suspended from 2¾" x 20" x 20" x 11 ga. steel pan supported by steel scissor arms and operated by two 1/8" aircraft cables with 2000 foot/pounds tensile strength per cable.

For SLX Models: Projector to be suspended from 31/4" x 24" x 26" x 11 ga. steel pan supported by steel scissor arms and operated by two, 3/16" aircraft cables with 4200 foot/pounds tensile strength per cable.

Equipped with 3 sets of stabilizing scissors, positioned on the left, right, and rear sides. Also equipped with fail-safe inertial safety belt system and Cable Management System with projector power cord. Factory set limit switches to automatically stop travel at store, show, and service positions. Single Station Control, standard, consists of one 12V toggle switch to lower lift from “stored” to “show ” positions, and one 12V momentary key switch to lower lift from “show” to

“service” position. Optional LVC-III for operation from “stored” to “show” positions only; required for use with Key Operated Switch.

Optional plenum housing consists of suitable painted steel panels for use in return air plenum situations. Optional ceiling closure panel, ﬁnished in white baked textured powdercoat, shall descend smoothly with projector. Choose a model based on number of feet needed (4'-9'/11'-17') to put projector within easy reach for servicing.

Please Note: The Scissor Lift should be speciﬁed in conjunction with a DRAPER motorized screen.

SMS Low Proﬁle Fixed Mount: Ceiling mount shall consist of a steel ball joint and Universal Projector Bracket. Mount shall be 2" long, and shall securely attach to lift with steel mounting plate (provided). Installer shall provide mounting hardware appropriate to ceiling conditions. Steel ball joint attaches to Universal Projector Bracket with twist-lock engagement. Min. overall height of assembled unit shall be 47/8". Mount shall provide up to 30° roll or pitch adjustment and 360° yaw adjustment at ball joint. Two setscrews lock ball joint in position. Max. load 26 lbs. Optional Ceiling Access Door: Provides access to projector and lift when unit is installed above hard ceiling. Choose one: [White painted ﬁnish/accepts ceiling tile].

Downloadable 3-part speciﬁcations are available at www.draperinc.com.

DRAPER SALESPERSON:

CUSTOMER CONTACT: