Dynasty Spas Dynasty Spa Control Panel Functions and Features Overview

K-4 keypad is mandatory when some options are selected. *

Filter cycles

The system automatically performs 2 filter cycles per day, at 12- hour intervals. During a filter cycle, Pumps 2 & 3 and blower run for one minute. Pump 1 then runs at low speed for the remaining of the cycle and "Filter Cycle" icon lights up. (If system is equipped with a circulation pump, all pumps and blower run for one minute. Circulation pump then runs for the remaining of the cycle and "Filter Cycle" icon lights up.)

Setting filter cycles:

1- Press Filter key.

FD10 2- The display will show FDxx, with "xx" representing the duration in hours.

3- Use Up and Down arrows to change setting. 4- Press Filter key again.

FS06 5- The display will show FSxx, with "xx" representing the delay before cycle starts.

6- Use Up and Down arrows to change setting. 7- Press Filter key to store settings.

40-minute filter cycle time-out: If you turn a pump, blower or light on during a filter cycle, the cycle will be interrupted and will only resume 40 minutes after the system has turned the last active output off.

Digital control pad lockout

This function allows you to prevent unauthorized parameter setting of the unit. This feature is especially helpful when young children have access to the keypad.

There are two modes you can choose from: Full lock or Partial lock. Full lock means that all keypad functions are locked. Partial lock means that the basic functions of the spa will remain accessible (pumps, blower and light), but it will be impossible to change the temperature Set Point, to override the Economy mode or to enter the Programming mode.

When control pad is locked, the "Lock" icon will be displayed.

Locking your digital control pad:

	1- Press and hold Econo key for 5 seconds.
LocP	2- The display will show LocP, with "P"
	representing Partial lock.
LocF	3- Release key and keypad will be in Partial lock
	mode. Keep key pressed down for 5 more
	seconds if you want to be in Full lock mode.
	The "LocF" message will then be displayed.

When control pad is locked, all automatic functions of the system run as usual. If a key is pressed down, a "LocP" or "LocF" message will be displayed for 1 second. To unlock the keypad, simply press and hold Econo key again for 5 seconds.

Purge cycles

The system can perform a number of purge cycles per day. During a purge cycle, pumps and blower run for two minutes and "Filter Cycle" icon lights up.

Setting purge cycles:

1- Press Filter key.

P 24 2- The display will show P xx, with "xx" representing the currently set number of daily purge cycles.

3- Use Up and Down arrows to change setting. 4- Press Filter key to store settings.

Boost filtration mode

This function allows you to speed up filtration after intensive use of your spa or to mix chemicals. Simply keep Pump 1 key pressed down for 5 seconds. Pump 1 will run at high speed for 45 minutes and "BOO" message will be displayed. Ozonator is also activated.

"CLE" message

Every two weeks, the "CLE" message might be displayed indicating to clean the filter (depending on your spa configuration). Press any key to reset the message.

Real-time clock *

Use Clock key to set real-time clock. The display toggles every 5 seconds alternately showing the hourly time and the current water temperature.

Water level sensor

If the system is equipped with an optional water level sensor and the sensor detects an insufficient level of water in the tub, the system will prevent pumps from starting and will display the "H20" message.

Pumps will be allowed to turn back on when water level returns above sensor.

Economy mode

To save energy, the Economy mode Set Point is 11˚C (20˚F) below the Normal mode Set Point.

The "Economy Mode" icon lights up when Economy mode is on.

Setting Economy mode:

	1- Press Econo key.
ED12	2- The display will show EDxx, with "xx"
	representing the Economy mode duration.
	3- Use Up or Down key to change setting.
	4- Press Econo key again.
ES20	5- The display will show ESxx, with "xx" representing
	the delay before mode starts.

6- Use Up and Down arrows to change setting. 7- Press Econo key a third time to store settings.

40-minute Economy mode time-out: If you turn a pump, blower or light on while Economy mode is on, the Economy mode will be interrupted and will only resume 40 minutes after the system has turned the last active output off. The "Econ" message or "Economy Mode" icon will flash, depending on your system configuration.

Inverted display

Press and hold Light key for 5 seconds to invert the display.

If a power-up occurs, the display always returns to default mode.

Summary of control panel parameters

FDxx Filter cycle duration

FSxx Filter cycle start delay

LocX Control pad lockout

EDxx Economy mode duration

ESxx Economy mode delay

P xx Purge cycles

C L U SIVE•

Smart

Winter Mode

9919-100614