Summary of control panel parameters, Time of day

7Step Programming Sequence

Temperature

unit

Step 1 Time of day

Step 2 Filter cycle start time Step 3 Filter cycle duration Step 4 Filter cycle frequency Step 5 Economy mode start time Step 6 Economy mode duration

Step 7 Storing settings in memory & returning to Normal mode

Filter Cycle
icon	Heater	Up & Down
Programming Mode	icon	arrows
Programming Mode
icon	Economy Mode
	icon	Lock
		icon

Step 1- Time of day

Setting the time:

1- Enter Programming mode by holding Prog. key pressed down for 2 seconds.

10:25 am 2- The display will show the current setting.

11:43	pm	3- Use Up and Down arrows to change
		setting.

Steps 2 & 3- Filter cycle start time & duration

The system automatically performs two filter cycles per day, at 12-hour intervals. During the filter cycle, Pumps 1 & 2 and the blower will run the first minute, then Pump 3 will run for one minute. Pump 1 will then run at low speed for a programmed number of hours. The "Filter Cycle" icon lights up when a filter cycle is on.

To program a filter cycle, you must enter: 1) the time you want the cycle to start and 2) the duration of the cycle. If no filtering is required, the duration should be set to "0". For continuous filtering, the filter cycle duration should be set to "12:00".

Setting filter cycle start time:

	1- Press Prog. key a second time.
FS01	2- The display will show FSxx, with "xx"
	representing the starting hour.
FS12	3- Use Up and Down arrows to change
	setting.

Setting filter cycle duration:

	1- Press Prog. key a third time.
Fd00	2- The display will show Fdxx, with "xx"
	representing the duration in hours.
Fd12	3- Use Up and Down arrows to change
	setting.

Step 4- Filter cycle frequency

Setting filter cycle frequency:

	1- Press Prog. key a fourth time.
FF01	2- The display will show FFxx, with "xx"
	representing the frequency per day.

	FF04	3- Use Up and Down arrows to change
	FF04	setting.
		setting.

Steps 5 & 6- Economy mode start time & duration*

Setting Economy mode start time:

	1- Press Prog. key a fifth time.
ES10	2- The display will show ESxx, with "xx"
	representing the starting hour.
ES08	3- Use Up and Down arrows to change
	setting.

Setting Economy mode duration:

1- Press Prog. key a sixth time.

Ed01 2- The display will show Edxx, with "xx" representing the duration in hours.

Ed04 3- Use Up and Down arrows to change setting.

Step 7- Storing settings in memory

Press Prog. key a seventh time to store settings in the system's non-volatile memory and to return to Normal mode.

Digital control pad lockout

This function allows you to prevent unauthorized parameter setting of the unit. This feature is especially helpful when young children have access to the keypad.

There are two modes you can choose from: Full lock or Partial lock. Full lock means that all keypad functions are locked. Partial lock means that the basic functions of the spa will remain accessi- ble (pumps, blower and light), but it will be impossible to change the temperature Set Point, to override the Economy mode or to enter the Programming mode.

When control pad is locked, the "Lock" icon will be displayed.

Locking your digital control pad:

1- Press and hold Pump 1 key for

5 seconds.

LocP 2- The display will show LocP, with "P"

representing Partial lock.

LocF 3- Release the key and the keypad will be in Partial lock mode. Keep key pressed down for 5 more seconds if you want to be in Full lock mode. The "LocF" message will then be displayed.

When control pad is locked, all automatic functions of the system run as usual. If a key is pressed down, a "LocP" or "LocF" message will be displayed for 1 second. To unlock the keypad, simply press and hold Pump 1 key again for 5 seconds.

Economy mode

Press Econo key to switch from Normal mode to Economy mode. To save energy, the Economy mode Set Point is 20˚F (11˚C) below the Normal mode Set Point.

The "Economy Mode" icon lights up when Economy mode is on.

There are 3 available Economy operating modes:

noEc: No Economy mode

Ec 1: Economy mode always on

Ec 2: Economy mode on during a programmed number of hours (see Steps 5 & 6*)

Selecting the desired Economy mode:

1- Press and hold Econo key for more than 2 seconds.

noEc 2- The display will show the current mode (noEc, Ec 1 or Ec 2).

Ec 1 3- Keep key pressed down until the desired mode is displayed.

After 5 seconds, the new setting will be programmed.

Inverted display

Press and hold Pump 2 for 5 seconds to invert the display. Note that the ˚F or ˚C icon is not displayed in reverse mode. Follow the same procedure to return to default mode. If a power-up occurs, the display always returns to default mode.