Dynex DX-GB8PRT Troubleshooting, Specifications, Legal notices, One-Year Limited Warranty

DX-GB8PRT_10-1124_QSG_V1.eps 2 10/29/2010 1:05:33 PM

Troubleshooting

1The power LED is not lit

Make sure that the power adapter is connected correctly and the power outlet is supplying power.

2The link/act LED is not lit when a device is connected to the corresponding port

Make sure that the cables are connected correctly and securely to the switch and device. Make sure that the cable is not longer than 328 ft. (100 m).

Specifications

Standards	IEEE 802.3, IEEE 802.3u, IEEE 802.3ab,
	IEEE 802.1p
Topology	Star
Protocol	CSMA/CD
Data transfer rate	Ethernet: 10 Mbps (Half Duplex),
	20 Mbps (Full Duplex)
	Fast Ethernet: 100 Mbps (Half Duplex),
	200 Mbps (Full Duplex)
	Gigabit Ethernet: 2000 Mbps (Full Duplex)
Network media (cable)	10Base-T: UTP category 3, 4, 5 cable
	(maximum 100 m)
	EIA/TIA-568 100Ω STP (maximum 100 m)
	100Base-TX: UTP category 5, 5e cable
	(maximum 100 m)
	EIA/TIA-568 100Ω STP (maximum 100 m)
	1000Base-TX: UTP category 5e, 6 cable
	(maximum 100 m)
	EIA/TIA-568 100Ω STP (maximum 100 m)
Number of ports	Eight 10/100/1000M RJ45 ports
LED indicators	Power, Link/Act
Transfer method	Store-and-Forward
MAC address learning	Automatic learning and aging
Frame filter rate	10Base-T: 14880 pps/Port
	100Base-Tx: 148800 pps/Port
	1000Base-T: 1488000 pps/Port
Frame forward rate	10Base-T: 14880 pps/Port
	100Base-Tx: 148800 pps/Port
	1000Base-T: 1488000 pps/Port
Operating temperature	32°F~104°F (0°C~40°C)
Storage temperature	-40°F~158°F (-40°C~70°C)
Operating humidity	10%~90% non-condensing
Storage humidity	5%~90% non-condensing

Legal notices

FCC statement

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more or the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

One-Year Limited Warranty

Visit www.dynexproducts.com for details.

Contact Dynex

For customer service please call 800-305-2204

www.dynexproducts.com

Distributed by Best Buy Purchasing, LLC

7601 Penn Avenue South, Richfield, MN USA 55423-3645 © 2010 BBY Solutions, Inc. All Rights Reserved.

DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names are trademarks of their respective owners.

ENGLISH 10-1124