QUICK SETUP GUIDE
Thank you for choosing the Dynex
Package contents | Tools you will need: | |||
A | Wall plate (1) | • | Power drill | |
B | Left TV bracket (1) | • 3/16 in. wood drill bit | ||
C | Right TV bracket (1) | • ½ in. masonry drill bit | ||
M4 Bag |
| • | Phillips screwdriver | |
| D | M4 × 12 mm screws (4) | • | Level |
| E | M4 × 30 mm screws (4) | • Socket wrench with ½ in. socket or | |
| F | M4 spacers (4) |
| adjustable wrench |
1Attach the TV brackets
Option 1: Attaching to a flat mounting surface
Attach the left and right TV brackets (B and C) to the back of the TV using: The M4 washers (G) and the M4 screws (D).
Or
The M6/M8 washers (N) and the M6 screws (H or I). Or
The M6/M8 washers (N) and the M8 screws (K)
NOTE: Adjust to shorten or hide the cords
2Install the wall plate
Option 1: Installing to a wood stud wall
1 Locate the studs. Verify the center of the stud with an awl or thin nail or use an edge to edge stud finder.
2Level the wall plate (A) and mark the hole locations.
3 Drill the pilot holes as illustrated.
4 Align the wall plate (A) with the pilot holes, then place the washers (P) over the holes. Insert the lag bolts (Q) through the washers, then tighten the lag
bolts only until the washers are pulled firmly against the wall plate. DO NOT
CAUTION: Avoid potential injuries or property damage!
Any material covering the wall must not exceed 5/8 in. (16 mm).
5/8 in. | 16 - | 24 in. | |
406mm | |||
- | |||
(<16 mm)** |
| 610mm | |
|
|
G | M4 washers (8) | • | Pencil |
M6 Bag |
| • | Stud finder |
H | M6 × 12 mm screws (4) | • | Awl |
IM6 × 20 mm screws (4) J M6 × 35 mm screws (4)
M8 Bag
K M8 × 16 mm screws (4)
L M8 × 40 mm screws (4)
M M6/M8 spacers (4)
NOTE: Determine if there is sufficient space |
|
between the back of the TV and the wall to |
|
connect all your cables before proceeding. | or |
You may need to use the optional spacers to |
|
allow more clearance between the back of |
|
the TV and the wall. |
|
or
or
N M6/M8 washers (4)
Lag Bolt Bag
O Wall anchors (3)
P 5/16 in. (7.9 mm) washers (3)
Q 5/16 in. × 2 ½ in. lag bolts (3)
M4 Bag
M4 × 12 mm | M4 × 30 mm |
M4M4
M6 Bag
M6 × 12 mm | M6 × 20 mm | M6 × 35 mm |
M8 Bag
M8 × 16 mm | M8 × 40 mm | M6/M8 | M6/M8 |
Lag Bolt Bag
5/16 in. | 5/16 × 2½ in. |
Option 2 Attaching to a rounded mounting surface
Attach the left and right TV brackets (B and C) to the back of the TV using: The M4 spacers (F), M4 washers (G), and the M4 screws (E).
Or
The M6/M8 spacers (M), M6/M8 washers (N), and the M6 screws (J). Or
The M6/M8 spacers (M), M6/M8 washers (N), and the M8 screws (L).
or
or
or
or
2.5 in.
(63.5 mm)*
*Drill the pilot hole to a depth of 2.5 in. (63.5 mm) **Maximum thickness of any material covering
the stud or concrete surface.