MIDI implementation

1. Note Mode setting

*The Note Mode setting lets you use MIDI note numbers to switch inputs.

*Use a system exclusive message to set the Note Mode.

*If the Note Mode is set to 49Keys Mode or Assign Mode, the velocity value of the note message will vary the transition time.

*The velocity value will control the transition time only when switching to the “A” channel if the video fader is at “A,” or when switching to the “B” channel if the video fader is at “B.”

*There are four Note Modes.

●1-1. OFF

*Note Mode is not used.

●1-2. 49Keys Mode

*If you select 49Keys Mode, the V-1 will be controlled by the following note numbers.

Note No.

Input

24H

A Ch. 1

26H

A Ch. 2

28H

A Ch. 3

29H

A Ch. 4

2BH

B Ch. 1

2DH

B Ch. 2

2FH

B Ch. 3

30H

B Ch. 4

●1-3. Assign Mode

*In Assign Mode, the V-1 will be controlled by the range of note numbers you specify using Note Assign. The factory settings are shown below.

*If you want to change the values used in Assign Mode, switch the Note Mode to Note Assign and make the desired assignments.

Note No.

Input

24H(C +2)

A Ch. 1

25H(C#+2)

A Ch. 2

26H(D +2)

A Ch. 3

27H(D#+2)

A Ch. 4

28H(E +2)

B Ch. 1

29H(F +2)

B Ch. 2

2AH(F#+2)

B Ch. 3

2BH(G +2)

B Ch. 4

●1-4. Note Assign

*In this mode you can modify the settings used in Assign Mode. You must specify two note numbers; a lower limit and an upper limit. When you have specified these numbers, the corresponding range of note numbers will be assigned to “A” channel 1, 2, 3,... through “B” channel 4.

(1) Change the Note Mode to Note Assign.

<Example> F0H 41H 10H 00H 6FH 12H 12H 00H 01H 03H 6AH F7H

(2)Specify the range of notes by transmitting two note-on messages with a velocity value of 1 or higher.

<Example> 90H 10H 7FH 90H 20H 7FH

(3)Transmit two note-on messages with a velocity of 0 for the specified range of notes.

<Example> 90H 10H 00H 90H 20H 00H

(4)Change the Note Mode back to Assign Mode.

<Example> F0H 41H 10H 00H 6FH 12H 12H 00H 01H 02H 6BH F7H

2. Parameter address map

●2-1. V-1 (Model ID = 00H 6FH)

*For addresses marked by #, divide the data and transmit it as two bytes; an upper nibble (upper 4 bits) and lower nibble (lower 4 bits).

*Example) If the original data is BCH, send 0BH as the first byte, and send 0CH as the second byte. For reception, the data will be ignored unless the two bytes are received together.

*DEVICE ID = 10H

Start Address

Description

00H 00H 00H

System Common Preference Area (See 2-1-1)

01H 00H 00H

Fader Control Preference Area (See 2-1-2)

02H 00H 00H

Effects Control Preference Area (See 2-1-3)

03H 00H 00H

Reserved Area

12H 00H 00H

Fader Control Parameter Area (See 2-1-4)

13H 00H 00H

Reserved Area

14H 00H 00H

Reserved Area

●2-1-1. System Common Preference

Address

Parameter Name

Sys.Ex.Value

Meaning of Value

00H 00H 00H

MIDI Receive Channel

00H - 10H.

1 - 16 Ch, OFF

●2-1-2. Fader Control Preference

Address

Parameter Name

Sys.Ex.Value

Meaning of Value

#01H 10H 00H

Tx/Rx Setting

01H-05H,07H-1FH,

Control Change,

 

(Transition Time)

40H-5FH,D0H,E0H,FFH

Channel Press,

 

 

 

Pitch Bend, OFF

#01H 10H 02H

Tx/Rx Setting

01H-05H,07H-1FH,

Control Change,

 

(Video Fader)

40H-5FH,D0H,E0H,FFH

Channel Press,

 

 

 

Pitch Bend, OFF

#01H 10H 04H

Tx/Rx Setting

01H-05H,07H-1FH,

Control Change,

 

(MIX, WIPE /

40H-5FH,D0H,E0H,FFH

Channel Press,

 

P in P)

 

Pitch Bend, OFF

#01H 10H 0AH

Tx/Rx Setting

01H-05H,07H-1FH,

Control Change,

 

(Output Fade)

40H-5FH,D0H,E0H,FFH

Channel Press,

 

 

 

Pitch Bend, OFF

●2-1-3. Effects Control Preference

Address

Parameter Name

Sys.Ex.Value

Meaning of Value

#02H 10H 00H

Tx/Rx Setting

01H-05H,07H-1FH,

Control Change,

 

(Superimpose)

40H-5FH, D0H, E0H,FFH

Channel Press,

 

 

 

Pitch Bend, OFF

●2-1-4. Fader Control Parameter

Address

Parameter Name

Sys.Ex.Value

Meaning of Value

12H 00H 01H

Note Mode

00H - 03H

OFF,49Keys Mode,

 

 

 

Assign Mode, Note Assign

●2-2. V-LINK (Model ID = 00H 51H)

*For addresses marked by #, divide the data and transmit it as two bytes; an upper nibble (upper 4 bits) and lower nibble (lower 4 bits).

*Example) If the original data is BCH, send 0BH as the first byte, and send 0CH as the second byte. For reception, the data will be ignored unless the two bytes are received together.

*If the value is shown as..., this is a parameter not supported by the V-1. It will be ignored if received.

*DEVICE ID = 10H

Start Address

Description

00H 00H 00H

DV-7PR Presenter Reserved Area

10H 00H 00H

V-LINK System Preference Area (See 2-2-1)

10H 10H 00H

V-LINK Clip Control Preference Area (See 2-2-2)

10H 20H 00H

V-LINK Effects Control Preference Area (See 2-2-3)

10H 30H 00H

V-LINK Reserved Area

11H 00H 00H

DV-7PR Presenter Reserved Area

25