]
TURNING ON / OFF PROJECTOR
TURNING ONTHE PROJECTORTURNING OFFTHE PROJECTOR
1Complete peripheral connections. (with a computer, VCR, etc.) before turning on the proJector.
2Connect the projector's AC power cord into an AC outlet. The LAMP indicator lights RED,and the READY indicator lights GREEN.
3Press the POWER
the cooling fans start to operate. The preparation display appears on the screen and the countdown starts.
4 After the countdown. the input source that was selected the last time and the Lamp control status icon
appear on the screen.
If the prOjector is locked with a PIN code, a PIN code Input DialogBox appears. Enter a PIN code as instructed below
To Enter a PIN code
Select a number by pressing the POINT LEFTIRIGHT button and fix the number with the SELECT button. The number changes to "*. ~ If you fixed a wrong number, move the pointer to "Set~ or ~Clear~
once by pressing the POINT DOWN button, then return to ~PIN code. ~ Enter the correct number.
00
Repeat this step to complete entering a four.(jigit number.
When the
operate the prOJector.
If you entered a wrong PIN code. UPIN code" and the number
(***.) turn red and disappear. Enter a PIN code all over again.
What is PIN code?
PIN (Personal Identification Number) code is a security code that allows the person who knows it to operate the projector. Setting a PIN code prevents unauthorized use of the projector.
A PIN code consists of a four digit number. Refer to PIN code lock function in SETTING Menu in the owner's manual for locking the operation of the projector with your PIN code.
The preparation display disappears after 30 seconds
Selected Input Source and Lamp control
F= |
| |
"" | I |
|
I tGI(/<C | I |
|
Q « |
| Lampcontrotstatus |
PIN code Input Di.log Box
~'" ...,. c:::=::::J$ ...L.Pointer
. I
..
co...
.. m. .0!CJ'" '"I
~After the OK icon disappears, you can operate the projector
1 Press the POWER
on the remote control, and "Power off?" appears on the screen.
2 Press the POWER
READY Indicator turns off. After the projector is turned
off, the cooling tans operate (for 90 seconds). During
this "cooling down" period, the projector cannot be turned on
3When the projector has .cooled down, the READY
Indicator lights GREEN agaIn and you can turn projector
on. After cooling down completely, unplug the AC power cord.
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
THE PROJECTOR ON, WAIT AT LEAST FIVE MINUTES BEFORE TURNING IT OFF
DO NOT UNPLUG THE AC POWER CORD WHILE COOLING FANS ARE RUNNING OR BEFORE THE
READY INDICATOR LIGHTS GREEN AGAIN. OTHERWISE IT WILL RESULT IN SHORTENING THE LAMP LIFE.
"'Note:
.The projector connor be rumed on during the cooling period with the
READY indi<awwmed off. You can wrn it on agarn after the READY
.indicator becomesGREENagain.
When the On srort funcrion is "On." rhis prOjector is turned on
O!Jromofically by connecting the AC power con:J to an AC O<Jr1et
.Continuous use may resulr in shortening the lamp life. Turn off the projectof-
.and resr ir for abour an hour.n every 24 hours.
The running speed of cooling fans is chonged according 0 the remperarure
.inside the PR1j«ror.
If rhe WARNING TEMP indicator blinks RED. see 'WARNING TEMP INDICATORHin the owners monoaf.
CAUTION ON HANDLING PIN CODe
If you forget your PIN code. the projector can no
longer be started. Take special care in setting a new PIN code; write down the number in a column on
page 60 of the owner's manual and keep it at hand
Should the PIN code be missing or forgotten, consult your dealer or service center