GENERAL INFORMATION
62.9694.01 Page 3
I . GENERAL INFORMATION
1. INSTRUCTIONS FOR SAFETY AND USE
1.1 INSTALLATION AND INITIAL OPERATION
1.2 OWNER'S OBLIGATIONS
1.3 USE AS PRESCRIBED
1.4 SAFETY-CONSCIOUS WORKING
1.5 AFTER-SALES SERVICE AND REPAIR
SThe installation, adjustment and initial opera-
tion of the appliance must be carried out
according to the manufacturer's instructions
and only by an authorised specialist.
SInstallations for the supply of electricity and
gas must be carried out by approved special-
ists in compliance with specific national and
local regulations. They bear the responsibility.
SThe appliance must not be placed in opera-
tion until the user has become familiar with its
operation. The operating instructions and the
related safety precautions must be followed
precisely. Follow strictly the attention and
warning label indications on the appliances.
SThe manager is responsible for ensuring that
all components relevant for safety are in per-
fect working order at all times. The operating
condition of these components must be exam-
ined by an authorized technician at least once
a year and any defects remedied if required.
SIf the safety valve in the boiler blows off, after-
sales service must be requested without
delay to establish the cause and remedy it.
SThe appliance must only be used for cooking
food in commercial kitchens. The appliance
has only been approved for supervised oper-
ation by trained persons.
SClosed containers (jars, cans, bottles, tubes,
etc.) must not be heated owing to the danger
of bursting and injuries.
SThe appliance must not be filled above the
level mark 4 cm below the boiler rim.
Depending on the type of food to be cooked,
filling must be less so as to prevent bubbling
over.
SThis appliance must not be used for deep fat
frying purposes. Do not use large cuantities
of oil. The appliance must not be operated
close to materials and vapours which consti-
tute a fire hazard.
SDuring operation, no objects are to be placed
on the lid
SOverheated oil can self-ignite. Never quench
burning oil with water, but smother the flames
with the cover or a wet cloth.
SSpraying the appliance or parts of it with a
high-pressure cleaning device may cause
malfunctions and is not to be done.
STo avoid damage to the appliance, do not let
water flow from the mixer tap onto the cook-
ing plates.
SWhen putting oil, fat, water or ingredients in
the preheated hot boiler, they may splash -
danger of burning!
SAlways use the handle to open the cover.
Note that while doing so, hot air or steam
may flow out or hot fat may spit out - danger
of burning!
SKeep your distance from the lid closing area
when closing the lid - danger of injury!
STo avoid damage to the appliance the mixer
tap outlet must be to the front before the lid is
opened or closed.
STilting is only to be carried out slowly to avoid
the contents spilling over the rim.
SHot steam can be expelled on opening the
lid. Staff must take appropriate measures
(stand well back) to avoid injuries.
SThe area around the tilting boiling pan must
be kept free. Tilting is only to take place with
the lid fully open.can spray. - danger of
burning!
SDevices on wheels set up in block configura-
tion must be checked before each start-up
whether the potential equalization is con-
nected with the neighbour equipment. The
connection may be done only by authorized
technical personnel.
SAppliances on wheels must be fastened with
the wall.
SBoiling pans of this design and operating
mode do not require special acceptance
tests. They are subjected to a pressure and
operating test which meets the regulations on
the manufacturer's premises. Recurrent
pressure testing is not compulsory. To ensure
the complete operating efficiency and safety
of appliances, however, owners should
arrange for personnel authorised by the man-
ufacturer to check on all safety equipment
and to conduct pressure tests at regular
intervals.
SIn the event of a permanent fault which inter-
feres with operation, the appliance must be
switched off and disconnected from the
power supply.
SRepair, maintenance work and other adjust-
ments are only to be carried out by an author-
ized specialist. The valid local and national
regulations must be observed. This applies
especially to burners, ignition, safety and con-
trol elements. Parts requiring replacement are
only to be replaced by original spare parts.
Periodic tests for gas leaks must be carried
out. A service contract is recommended.
SCleaning and maintenance must be done only
when the heating surfaces are cold. Do not
use inflammable liquids to clean the appli-
ance.
SAn obligatory service check is required
annually.