![](/images/backgrounds/275045/bgc.png)
12
ENGLISH
•Check V-belt:
−Remove belt guard (30).
−Retension V-belt or replace, if
necessary.
−To adjust the V-belt tension,
loosen the four screws at the
motor base and shift the motor.
−Tighten the screws at the motor
base again.
−Replace the belt guard.
Every 250 operating hours
•Replace air intake filter element of
compressor pump.
•Replace air filter element of filter/
regulator unit.
Every 500 operating hours
•Drain oil from compressor pump
through the drain plug (28) and fill
with fresh oil.
ADispose of the waste oil envi-
ronmentally safe by taking it to a
proper collecting point!
Every 1000 operating hours
•Have unit serviced by an authorized
service station. This will extent the
compressor's service life considera-
bly.
5.2 Device storage
1. Switch unit OFF and unplug.
2. Release pressure from tank and all
connected air tools.
3. Store device in such way that it can-
not be started by unauthorized per-
sons.
ACaution!
Do not store device unpro-
tected outdoors or in damp environ-
ment.
Do not lay device on its side for trans-
portation or storing.
For special applications the following
accessories are available at your spe-
cialist dealer – see back cover for illus-
trations:
Sealing
AAir Caulking Gun KP 910
for commercially available car-
tridges.
Stock-no. 090 101 0030
Sheet metal cutting
BAir Nibbler BN5 40
extra small cutting radius; cuts steel
sheet up to 1.0 mm thickness.
Stock-no. 090 100 6784
Drilling
CAir Drill BM3 10
especially handy tool for low-fatigue
working; right-hand rotation only.
Stock-no. 090 100 6725
•Air Drill BM50 0 (not shown)
with 3/8" keyless chuck, fully revers-
ible with quick reverse feature.
Stock-no. 090 105 4533
Stapling / nailing
DCombination Air Stapler/Nailer
Kombi 40/50
for staples (type 90) from 20 mm to
40 mm and finishing nails (type
SKN) from 20mm to 50.
Stock-no. 090105 4720mm.
•Combination Air Stapler/Nailer
Kombi 32 (not illustrated)
for staples (type 90) from 15 mm to
32 mm and finishing nails (type
SKN) from 16 mm to 32.
Stock-no. 090 105 4711mm.
•Air Stapler KG 80/16
(not illustrated)
for staples (type 80) from 6 mm to
16 mm.
Stock-no. 090 105 4681
•Air Stapler KG 90/25
(not illustrated)
for staples (type 90) from 15 mm to
25 mm.
Stock-no. 090 105 4690
•Air Stapler KG 90/40
(not illustrated)
for staples (type 90) from 20 mm to
40 mm.
Stock-no. 090 105 4703
•Air Finish Nailer SKN 50
(not illustrated)
for finishing nails (type SKN) from
20mm to 50 mm.
Stock-no. 090 105 4738
Spray painting
ESpray Gun FB 2200H VLP
high-volume low-pressure feature
reduces paint mist bounce-back
and provides thicker coating at less
paint consumption.
Stock-no. 090 105 4460
•Paint Spray Gun FB2200
(not illustrated)
with 0.5 l flow cup; professional
spray gun; steplessly adjustable
round, horizontal and vertical spray
pattern.
Stock-no. 090 105 4452
•Paint Spray Gun SB200
(not illustrated)
with 1.0 l siphon cup.
Stock-no. 090 100 3882
•Paint Spray Gun FB150
(not illustrated)
with 0.5 l flow cup; for spraying prim-
ers and paints of varying viskosity.
Stock-no. 090 100 3874
•Paint Spray Gun FB90 (not illus-
trated)
with 0.75 l flow cup; for spraying
primers and paints of varying vis-
cosity.
Stock-no. 090 105 6064
Chiselling
FAir Hammer Set MHS450
for construction and auto body work
Stock-no. 090 100 9210
•Air Hammer Set MHS315
(not illustrated)
to take off plaster and tiles and for
light chiselling work.
Stock-no. 090 100 6911
Tyre inflating / checking
GTyre Inflator Gauge RF 480
professional version
(calibrated).
Stock-no. 090 105 4630
•Tyre Inflator Gauge RF 363
(not illustrated)
same as RF 480, but not calibrated.
Stock-no. 090 105 4622
•Tyre Inflator Gauge RF 200
(not illustrated)
for inflating tyres and balls (cali-
brated).
Stock-no. 090 105 6188
•Tyre Inflator Gauge RF 100
(not illustrated)
same as RF 200, but not calibrated.
Stock-no. 090 102 6724
Cleaning
HBlow Gun BP 200
all plastic body.
Stock-no. 090 105 4606
•Blow Gun BP 300 (not illustrated)
all plastic body; venturi nozzle pro-
vides extra high air volume.
Stock-no. 090 105 4614
30