Emerson CF705BS03, CF705TG03, CF705WPB03, CF705NW03, CF705S03 How to Put Your Ceiling Fan Together

How to Put Your Ceiling Fan Together

1.Pass the 80" motor leads through the opening in the ceiling cover. Be sure the cover is oriented correctly (Figure 1).

2.Separate, untwist and unkink the three motor leads. Route the motor leads through the hanger ball/downrod assembly.

3.Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 1). The cle- vis pin must go through the holes in the motor cou- pling and the holes in the downrod. Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved por- tion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to pre- vent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed.

!WARNING

It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tightened. Failure to verify that the pin and setscrews are properly installed could result in the fan falling.

	MOTOR
3/16-24 x 1/2"	COUPLING
SETSCREW	HAIRPIN
CLEVIS PIN
	CLIP

JAMNUT

HANGER BALL/

DOWNROD ASSEMBLY

CEILING

COVER

CLEVIS	CLEVIS
PIN	PIN
3/16-24 x 1/2" SCREW	HAIRPIN
WITH JAM NUT	CLIP

MOTOR COUPLING

Figure 1

4.Back off the jam nut until it rests loosely against the setscrew head. Install the setscrew in the motor coupling (Figure 1) and tighten securely while

pulling up on the downrod. Using a 5/16-inch open end wrench or pliers, tighten the jam nut securely against the motor coupling.

NOTE: The setscrew and jam nut must be properly installed as described above, or fan wobble could result.

5.The fan comes with blue, black and white leads that are 80-inches long. Before installing the fan, measure up approximately 6 to 9-inches above top of hanger ball/downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads.

6.Mount blade flanges to fan blades using three 3/16-24 x 5/16” slotted Phillips screws and three

blade washers (Figure 2). 4

!WARNING

To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, bal- ancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

3/16-24 x 1/4" SLOTTED PHILLIPS SCREW (3)

BLADE WASHER (3)

	FAN BLADE
Figure 2	BLADE FLANGE

NOTE: Take care not to scratch fan housing when installing blades.

NOTE: Remove and discard the four shipping spacers and screws from the motor hub.

7.Turn the fan assembly upside down in preparation for mounting the fan blade assemblies.

8.Rotate the motor hub until the flange screw hole is next to the cutout in the switch housing plate. Attach one blade assembly to the motor hub using two 1/4- 20 x 1/2” Phillips oval head flange screws. Make sure the screws are NOT tightened. (Figure 3.) Repeat this procedure for the other four blade assemblies.

SWITCH HOUSING	BLADE FLANGE
PLATE

MOTOR HUB	1/4-20 X 1/2" PHILLIPS OVAL
	HEAD FLANGE SCREWS (2)

Figure 3

9.The blade flanges have an interlocking feature that must be fully engaged before tightening the screws. Make sure all the flanges are properly engaged and then tighten the flange screws. If one of the flanges does not seat properly on the motor hub, loosen the adjacent flange screws, re- engage and reseat the flanges, then tighten the screws again.

10.Engage the connector of the switch housing assembly with the motor connector (Figure 4). The two connectors are keyed and color-coded and must be mated correctly (color-to-color) before they can be engaged. Make sure the con- nector latch closes properly.