Cleaning Your Humidifier, Step To Remove Parts

SP6551 manual - 71238 7/12/05 1:56 PM Page 11

Cleaning Your Humidifier

CAUTION: To reduce the risk of injury, fire or damage to humidifier, use only cleaners specifically recommended for humidifiers. Never use flammable, com- bustible or poisonous materials to clean your humidifier. To reduce the risk of scalds and damage to humidifier, never put hot water in humidifier.

CAUTION: Local water purity may vary from area to area and under certain conditions water impurities and air- borne bacteria may promote the growth of microorganisms in the reservoir of a humidifier.

To retard bacteria growth that may cause odors and be harmful to your health, use only Emerson replacement filters. We also recommend using an EPA registered liquid bacteriostat, and cleaners specifically recommended for evaporative humidifiers available at your local retail store.

NOTE: If it is necessary to use an approved bacteriostat, follow the directions correctly. The bottles of this unit will hold 2-3/8 gallons or 9 litres of water each.

Step 1

To make cleaning easier, the humidifier cabi- net should be empty and completely dried out. To accomplish this, use the following method:

a. Allow the humidifier to run until the auto- matic shutoff turns the humidifier “OFF”.

b. Unplug humidifier

WARNING: If humidifier is not un- plugged, fan could start after housing is removed.

Step 2

To Remove Parts

a. Open the pivoting lid and remove water bottles and set aside. Grasp the fan assembly front center and rear center. Lift

off and set aside on a clean flat surface. The filter housings are now accessible.

b. Before removing the internal parts of the humidifier cabinet, we recommend moving the humidifier to an area where floor cov- erings are not susceptible to water dam- age, i.e., kitchen or bath area. Lift the filter housing assemblies out of the cabinet and set to the side.

c. Remove the water level float from the humidifier cabinet by pinching the float retainer at the back of the cabinet to release it. The cabinet should be empty before cleaning. The cabinet consists of the lower areas of the humidifier where the filters are during normal operation time.

d.Empty cabinet of any remaining water.

e.Proceed to “Bi-Weekly Maintenance” or “End of Season Maintenance” then contin- ue as described below.

f.Remove old filters and dispose of properly as described on page 9 and 10.

Step 3

Install new filters (use Emerson Replacement Filters) into the location where the old filters were positioned. Install water level float at back of cabinet. Ensure that you slide the float retainer down to the lowest position in slot at back of cabinet. (See dia- gram of slot below). Install the filter housings with the new filters into the correct location. Position the fan assembly on top of the cabi- net and return the humidifier to the desired location for use.

Refill humidifier bottles with fresh cool water. Plug the unit into a 120 volt A.C. power outlet and set the controls per the “Operating Humidifier Controls” section of this manual.

Back of Cabinet

BOTTOM POSITION

IS FOR NORMAL

OPERATION MODE

FLOAT

RETAINER

SLOT

HD1405 specifications

The Emerson HD1405 is a pioneering solution in the realm of process automation, designed to enhance efficiency, reliability, and accuracy in industrial operations. As part of Emerson's advanced instrumentation portfolio, the HD1405 stands out for its blend of cutting-edge features and user-friendly design.

One of the HD1405’s main features is its robust data acquisition capabilities. It is equipped with high-speed processing power that allows for real-time monitoring and control of various processes. The device can capture and analyze data from multiple sources simultaneously, ensuring that operators have access to crucial information at their fingertips.

Another notable aspect of the HD1405 is its integration of advanced diagnostic tools. These tools leverage predictive analytics to anticipate potential equipment failures before they occur. This proactive approach helps to minimize downtime and enhances the overall reliability of the industrial processes being monitored. With features like self-diagnostics and trend analysis, the HD1405 empowers operators to make informed decisions based on comprehensive data insights.

The Emerson HD1405 also supports a wide array of communication protocols, providing seamless connectivity with existing systems. Its compatibility with various industry standards ensures that it can be easily integrated into any automation architecture, thus facilitating point-to-point communication as well as connection to larger networks.

In terms of user experience, the HD1405 features a highly intuitive interface. Operators can navigate through settings and data with ease, thanks to the device's clear graphical displays and logical layout. This user-centric design minimizes the learning curve for technicians and allows for efficient training and onboarding processes.

Additionally, the HD1405 is designed to endure harsh industrial environments. Its durable construction and rugged design enable it to withstand extreme temperatures, vibrations, and contaminants commonly found in process industries. This reliability in challenging conditions makes it an ideal choice for a wide range of applications, from oil and gas to chemical processing and beyond.

In summary, the Emerson HD1405 is a versatile and sophisticated device that combines advanced data acquisition capabilities, predictive diagnostics, multi-protocol connectivity, and user-friendly design. Its robust characteristics position it as an invaluable tool for optimizing industrial processes and fostering operational excellence. As industries continue to evolve, the HD1405 remains at the forefront of automation technology, helping businesses achieve their goals with efficiency and precision.

Emerson HD1405 owner manual Cleaning Your Humidifier, Step To Remove Parts

Models: HD1405