5.1 Analyzer Module Setup

5.1.7 Programmable Calculator

Main Menu — Analyzer and I/O-module expert configuration

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer module setup

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Programmable calculator

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TAG

 

 

 

 

 

 

 

 

95.00 ppm

 

 

 

 

 

 

 

 

 

 

 

-- Programmable Calculator --

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Programming...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Constants...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Units...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Calculator is:

 

 

 

 

 

 

 

Enabled

 

 

 

 

 

 

 

 

Scaling...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Result Calculator 1:

 

 

 

 

 

0.012

Vol%

 

 

 

 

 

 

 

 

Result Calculator 2:

 

 

123.000

ppm

 

 

 

 

 

 

 

 

Result Calculator 3:

 

 

 

 

 

 

 

 

_

 

 

 

 

 

 

 

 

Result Calculator 4:

 

 

 

 

 

 

 

 

_

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Measure

 

 

 

 

 

 

Back...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

F2

F3

 

F4

 

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "Programmable Calculator" you can start the calculation with variables of the MLT analyzer or analyzer module selected, e.g. conversion of concentrations from ppm to mg/m3. You have four memory places to calculate results. The required program and further conditions have to be set up in several submenus. The calculation with values of auxiliary modules is not possible!

Set up parameters:

¨Select the line of variables or any menu line with the ↓ -key or the − -key.

¨Select the variable or change to the submenu with the 8 -key or the → -key.

¨Select "Enabled" or "Disabled" in the line "Calculator is" with the − -key or the ↓ -key.

¨Confirm the parameter selected with the 8 -key or cancel and go back to the last value with the F2 key.

Programming and starting of the calculator (+Consider the example p. 5-47/48 !):

1)Disable the calculator:

·Before you will begin with the programming, you have to select "Disabled" in the line "Calculator is" to avoid starting calculation while you are writing the program.

2)Putting in the program:

·Press the 8 -key or the → -key in the line "Programming..." to change to the sub- menu "Program", where you can put in your program step by step.

·A program of a calculator consists of operands like concentration or flow and of operators like the addition command. You have to put in a certain code in each program line for each operator and each variable or constant.

90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98

NGA 2000

5 - 45