6.3.2.3 Diagnostic Menus

Physical Measurements

Main Menu — Technical level configuration

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Diagnostic menus

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer module diagnostics

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Physical Measurements

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

 

 

 

Physical Measurements

 

340 hPa

 

 

 

 

 

 

 

 

Sample capillary pressure:

 

 

 

 

 

 

 

 

 

 

 

 

Ozone supply pressure:

 

 

 

 

1030 hPa

 

 

 

 

 

 

 

 

Ozonator status:

 

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

Ozonator power:

 

 

 

 

 

Enabled

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bypass flow:

 

 

 

1100 ml/min

 

 

 

 

 

 

 

 

Converter temperature:

 

 

 

 

 

360 C

 

 

 

 

 

 

 

 

Sensor temperature:

 

 

 

 

 

0.5 C

 

 

 

 

 

 

 

 

Block temperature:

 

 

 

 

 

51.5 C

 

 

 

 

 

 

 

 

Capillary flow rate:

 

 

 

 

200 ml/min

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pressure limits...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Temperature limits...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOME

 

ESCAPE

 

 

 

HISTORY

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

 

F2

F3

 

F4

 

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "Physical Measurements" you can find several physical measurement parameters of the CLD analyzer module like ozonator power, converter temperature or capillary flow rate. Via the menu lines "Pressure limits..." and "Temperature limits..." you can change to the corresponding submenus, where you can set up several pressure parameters and temperature parameters of the analyzer.

The violation of the limits in the submenus may start alarm reports, if the alarm report is enabled in the menu "Analyzer Diagnostics" (see 6.3.2 p. 6-27). Besides, the limits of the submenus will be begin and end of the bargraphs in the single component display, if activated (see 5.1.9 p. 5-24).

You can also reach the menu "Physical Measurements" via the menu "Analyzer module set up" of the expert controls and set up menus (chapter 5.1.10 p. 5-26).

Changing to the submenus:

¨Select the line you want with the − -key or the ↓ -key.

¨Press the ENTER key or the → -key to change to the corresponding submenu.

Note:

You should control the sample capillary pressure, the ozone supply pressure and the bypass flow in this menu after starting up your CLD. The values displayed in these lines should be equivalent to the original manufacturer's data sheet to avoid measurement errors.

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98

NGA 2000

6 - 33