4.2.2 Calibration - Spanning
CLD |
|
|
| 225.0 ppm |
|
| Main Menu |
|
|
Basic controls... |
|
|
| |
Expert controls and set up... |
|
| ||
(Operational configuration) |
|
| ||
Technical level configuration... |
|
| ||
(Diagnostic and manufacturing/service) |
| |||
MEASURE | STATUS | NEXT | LOCK | INFO |
F1 | F2 | F3 | F4 | F5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CLD |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| 225.00 |
|
|
|
|
|
|
| ppm NOx |
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 |
|
|
| Range: 4 |
|
|
| 250 |
|
|
|
|
|
|
|
|
| ||||||||
| Sample press.: |
| 340 hPa |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
| Detector temperature: | 0.5 | C |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
| Block temperature: |
|
| 51.5 | C |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
| Converter temp.: |
|
| 360 | C |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| DISPLAY |
| STATUS |
| MENU |
| NEXT |
|
| INFO |
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| F1 |
|
|
| F2 |
|
|
| F3 |
|
|
| F4 |
|
|
| F5 |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
⇒Change to the single component display
F1
Press
⇒Single component display will appear after the span gas calibration
⇒Notes for the span gas calibration:
·You can calibrate all ranges together or each range separately with span gas. You have to set up the parameter you want in the menu "Calibration Parameters" (see chapter 5.1.2 p.
·If it will not be possible to calibrate all ranges with the same span gas, you have to calibrate each range separately!
·The desired value of span gas has to be (!) a value between 10% and 110% of each end of range. Otherwise, no calibration will be running.
Example:
· End of range 1: 50 ppm
·End of range 2: 250 ppm
·End of range 3: 1000 ppm
·End of range 4: 2500 ppm
® | Potential span gas setpoints: | 5 | – | 55 ppm |
® | Potential span gas setpoints: | 25 | – | 275 ppm |
®Potential span gas setpoints: 100 – 1100 ppm
®Potential span gas setpoints: 250 – 2750 ppm
90003749(1)
NGA 2000 | 4 - 27 |