5.1.2 Analyzer Module Set up

Calibration Parameters

Main Menu — Expert controls and set up

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Analyzer module set up

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Calibration parameters

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

 

 

 

Calibration Parameters

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Calibration adjustment limits:

 

 

 

 

Disabled

 

 

 

 

 

 

 

 

 

Calibration averaging time:

 

 

 

 

 

5 s

 

 

 

 

 

 

 

 

 

Calibration failure alarm:

 

 

 

 

 

No

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cal. failure error allowed:

 

 

 

50 %

 

 

 

 

 

 

 

 

 

Calibration time out:

 

 

 

 

 

 

 

 

 

60 s

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zero ranges:

 

 

 

 

 

 

 

TOGETHER

 

 

 

 

 

 

 

 

Span ranges:

 

 

 

 

 

 

 

SEPARATELY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOME

 

ESCAPE

 

 

 

 

 

 

 

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

 

F2

 

F3

F4

 

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "Calibration Parameters" you can set up several parameters of the zero and span calibration.

Set up parameters:

¨Select the line of variables you want with the ↓ -key or the − -key.

¨Select the variable with the ENTER key or the → -key.

¨Select any digit with the ← -key or the → -key and adjust a new value with the − -key or the ↓ -key

resp. select the whole parameter with the − -key or the ↓ -key.

¨Confirm the new value with the ENTER key or cancel and go back to the last value with the F2 key.

Line of variables "Calibration adjustment limits:

¨Enabled: The calibration result will only be accepted within the limit settings. If the results will be out of these limits, you will find a corresponding error message in the menu "Analyzer zero" respectively "Analyzer span". Illustrations of these menus you will find in chapter 4.2.1 p. 4-22resp. 4.2.2 p. 4-26.

¨Disabled: The calibration will be possible, even if the calibration results will leave the allowed limits. Compare with the explanations in chapter 5.1.1 p. 5-6/7.

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98

NGA 2000

5 - 9