5.2.2 Auxiliary Module Controls

Set-up DIO module(s)

Main Menu — Expert controls and set up

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Auxiliary module controls

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Set-up DIO module(s)

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

 

 

- DIO-MODULE OUTPUTS -

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Inputs...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Outputnumber:

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

Choose module...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Choose signal...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Invert output:

 

 

 

 

 

 

 

 

 

Disabled

 

 

 

 

 

 

 

 

Module status:

 

 

 

 

 

 

 

 

 

Normal

 

 

 

 

 

 

 

 

Slot ID:

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

Signal name:

 

 

 

 

 

 

 

 

 

????

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal level:

 

 

 

 

 

 

 

 

 

 

 

 

Off

 

 

 

 

 

 

 

 

Signal comes from:

 

 

 

 

 

 

 

 

 

????

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXPERT

 

 

 

 

>>>

 

ACKNOWL

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

F2

 

F3

F4

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "DIO-MODULE OUTPUTS" you can set up the output configuration of the DIO modules combined to the control module (platform or MLT analyzer). Besides you can change to the submenu "DIO-MODULE INPUTS" to configure the inputs of the auxiliary DIO modules.

Every DIO module is composed of 8 digital inputs and 24 digital outputs. If there exist several DIO modules in the platform you can change to the setup menu of each with the F3 key. The tag number of the DIO board selected will appear in the line "Slot ID". The changing with the F3 key is not available for MLT analyzers because only one DIO can be installed in it.

The 24 digital outputs are composed of 3 units with 8 outputs. If there is a short circuit or an overload in one unit it will be switched off and saved against destruction. After the defect is removed the board is available immediately. You only have to press the F4 key. Informations about the whole specification of the DIO board you will find in another manual.

Set up parameters:

¨Select any line of variables or any menu line with the ↓ -key or the − -key.

¨Select the variable or change to the submenu with the ENTER key or the → -key.

¨Adjust a new value or select the whole parameter with the − -key or the ↓ -key.

¨Confirm the new value with the ENTER key or cancel and go back to the last value with the F2 key.

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98

NGA 2000

5 - 39