6
INSTALLER/CONFIGURATION MENU
To enter the menu: Press the Menu touch key. Press and hold for 5 seconds the Installer Config touch key. This displays screen reference #1 in the table below. Screen Reference numbers appear in top right corner of display. Press to advance to the next menu item or to return to a previous menu item. Press or to change a menu item option. Shaded items are not available if selected for Non-Programmable. Write the options selected in the "Option Selected" column of the menu.Installer Note: To default the programming, clock and Configuration Menu to the Factory Default Settings, press the ,and SYSTEM keys simultaneously. The thermostat display will go blank for a few seconds, and then all segments will display momentarily. For heat pump systems, Configuration Menu items 1 and 3 must be set to match the heat pump system.

CONFIGURATION MENU

Screen

Reference

Number

SS1

MS2

HP1

HP2

Press

key

Displayed

Factory

(Default)

Press or

to select from

listed options

Comments Option

Selected

1  MS 2 HP 1, HP 2, SS 1 Selects Multi-Stage (MS2, No Heat Pump), Heat Pump 1
(HP1, 1 compressor), Heat Pump 2 (HP2, 2 compressor
or 2 speed compressor), or Single Stage.
2  (GAS) ELE GAS setting: furnace controls blower.
ELE setting: thermostat controls blower.
30b (0) b Selects Reversing Valve (This item is only to appear if HP1 or HP2
is selected above.)
4  Days, (7) P 5 or 0Programs per week. (7 days, 5+1+1 days or non-programmable)
5  (4) PS 2 Programs per day.
4 = Morning, Day, Evening, Night
2 = Day, Night
Not available if 4 is 0
6Cool-Off-
Heat-Auto
Cool-Off-Heat, Heat Off,
Heat, Cool-Off, Auto Off
System switch configuration in non heat pump mode.
Cool-Off-Heat-
Em-Auto
Cool-Off-Heat-Em,
Off-Em-Auto
System switch configuration, heat pump mode.
7  (On) EOFF Selects Energy Management Recovery. Not available if 4 is 0
8  (FA) Heat, Cr SL Selects Adjustable Anticipation, cycle rate, Heat
9  (FA) Cool, Cr SL Selects Adjustable Anticipation, cycle rate, Cool
10 (FA) Cr/AU, Em SL Selects Adjustable Anticipation, cycle rate auxiliary, (This item is
only to appear if HP1 or HP2 is selected above).
11   (OFF) CL On Selects Compressor Lockout.
12   (On) dL OFF Selects Continuous Display backlight.
13   0
(Temperature)
5, LO to 5, HI Selects Adjustable Ambient Temperature Display [range -5 (LO) to
+5 (HI)].
14   °F °C Selects °F/°C Display (temperature units in Fahrenheit or Celsius).
15   (On) bOFF Selects audible Beeper On/Off.
16   (On) dS OFF Selects Daylight Saving Time calculation.
17   (On) Heat, AS OFF Selects Automatic Schedule for comfort temperature Programming,
heat mode. Not available if 4 is 0
18   (On) Cool, AS OFF Selects Automatic Schedule for comfort temperature Programming,
cool mode. Not available if 4 is 0
19   (OFF) CS On Selects Cool Savings Feature On of Off.
20   CS Cool Savings
(3)
1-2-3-4-5-6 Selects amount of Cool Savings adjustment.
21   (Off) CO On Select Compressor Optimization (not available on earlier models)
22   (OFF) CA On Selects Comfort Aler t Feature On or Off. (not available on earlier
models)
23   (99) Heat, HL 62-98 TEMPERATURE LIMIT, HEAT (max. heat set point).
24   (45) Cool, LL 46-82 TEMPERATURE LIMIT, COOL (min. cool set point).
25   OFF,
Keypad Lockout
L (total), P (partial),
Temperature Limit
(limited temperature range)
Selects Keypad Lockout.
26   000 001-999 Selects Keypad Lockout Combination (active only if keypad Lockout
is selected).
27   (On) Heat, FS OFF Fast second stage of heat (not available if SS1 is selected above).
28   (On) Cool, FS OFF Fast second stage of cool (not available if SS1 or HP1 is selected
above).
29   Remote (OFF) On Remote temperature sensor, enable/disable.
30   Remote, In Outdoor Remote Remote temperature sensor (Indoor/Outdoor).
31   (On) LS OFF Local temp. Sensor enable/disable (only when Indoor Remote is
selected On).
32 (OFF) dF On Selects Dual Fuel feature On or OFF (this item appears if HP1 or
HP2 is selected above).