9MAKE FINAL PLUMBING CONNECTIONS

Product Damage

•Make sure bends in all tubes are smooth and unkinked before you proceed.

•Make sure all tubes are not twisted, pinched or blocked.

•Do not extend the two water lines to the tank beyond the 16" (40cm) provided.

•Pinched or blocked water lines may cause access pressure and damage the dispenser tank.

1.Slip plastic nut over 1/4" copper inlet tube. Insert tube into threaded inlet fitting until you feel it stop. Be sure copper tube is straight.

2.Align plastic nut and tighten by hand. Use caution to avoid cross-threading nut. Next, use a small adjustable wrench to slowly tighten nut 1-2 turns past finger tight until tube is snug. If tube is not snug after two full turns, remove nut, and check that tube is fully seated. Then retighten nut NOT MORE THAN THREE (3) FULL TURNS past finger tight.

Product Damage

Overtightening the plastic nut can break the inlet fitting.

3.Connect clear plastic vent line to smallest (center) fitting by squeezing hose clamp with pliers, positioning clamp/hose on fitting, and releasing to secure.

4.Finally, connect 7/16" flexible outlet tube to remaining fitting by squeezing hose clamp with pliers, positioning clamp/hose on fitting, and releasing to secure. Note: Ensure that the flexible plastic vent and outlet tubes are not twisted, pinched or blocked.

10FILL TANK

1.Make sure shutoff valve is turned on. Then turn handle, left or right, or up or down, and hold open.

2.After about one minute, tank will fill and water will flow from dispenser spout. Check all water connections for leaks. If water leaks, check all fittings and tighten if necessary.

Product Damage - DO NO PLUG IN YET

Do not plug unit in until tank is filled with water and water flows from spout.

Electric Shock Hazard - This Appliance Must be Properly Grounded.

•Do not alter or remove the ground pin from the power supply cord.

•Using an ungrounded appliance can result in serious injury or death from electric shock.

9

-1

9

-3

9

-2

9

-4

This appliance must be grounded. In the event of a malfunction or break- down, grounding provides a path of least resistance for electric current to reduce risk of electric shock. This appliance is equipped with a cord having an equipment grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

•mproperI connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if your are in doubt as to whether the appliance is properly grounded.

•Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

•Once the electrical cord is plugged in, it will take 10 to 15 minutes for the water to reach its 190˚F (88˚C) (approximate) temperature.

•During the heating cycle you can expect to hear gurgling or hissing sounds within the tank. This is normal. The unit may boil briefly on initial start-up until the temperature sensing system reaches equilibrium. This is also normal. Boiling is indicated by steam or hot water spurting from the dispenser spout without actuating the dispenser handle.

•If your dispenser is boiling, carefully activate the dispenser handle for about 20 seconds to draw off that steaming hot water and allow the water in the tank to reheat. Repeat this step one or two more times. Do not allow the dispenser to continue to boil.

•If the dispenser continues to steam or boil it will be necessary to adjust the thermostat slightly to decrease the water temperature. Refer to temperature adjusting procedure and warnings.

High Altitudes: Because the boiling point of water is reduced at higher elevations (e.g. Denver, Colorado) it may be necessary to decrease the temperature setting to keep the unit from boiling. Refer to temperature adjusting procedure and warnings.

11PLUG IN THE UNIT

Product Damage

Do not plug unit in until tank is filled with water and water flows from spout.

10 -1

10 -2

INSTALLATION QUESTIONS?

Call the Answerline at 1-800-558-5700

Page 4 Page 6
Page 5
Image 5
Emerson Process Management Water Dispenser warranty Make Final Plumbing Connections, Fill Tank, Plug in the Unit
Page 4 Page 6

Water Dispenser specifications

Emerson Process Management has pioneered innovative solutions in the field of process automation, and its water dispenser exemplifies the synergy of technology and user experience. This advanced water dispenser is designed for both residential and commercial use, providing a reliable source of purified drinking water with exceptional efficiency and convenience.

One of the main features of the Emerson water dispenser is its multi-stage filtration system. This system leverages advanced filtration technologies including activated carbon and reverse osmosis to remove contaminants, ensuring that the water not only tastes great but is also safe for consumption. Users can enjoy peace of mind knowing that the water dispensed is free from harmful substances, making it particularly beneficial in areas with less-than-ideal water quality.

The Emerson water dispenser also boasts a sleek and modern design, making it a stylish addition to any environment. Its user-friendly interface enables easy operation, allowing users to select different temperature settings, from refreshing cold water to soothing hot water, at the touch of a button. This feature is particularly useful for varied uses such as making tea, coffee, or instant soups.

In terms of smart technologies, the Emerson water dispenser is equipped with smart sensors that monitor the water levels and filter life, sending alerts when it's time for a refill or filter replacement. This ensures users are always aware of the maintenance needs of their system, preventing unexpected downtime. Additionally, some models include connectivity features allowing users to manage their water consumption and settings via a mobile app, enhancing the overall user experience.

Energy efficiency is another hallmark of Emerson’s water dispenser. With eco-friendly modes and energy-saving features, the device operates optimally while minimizing electricity usage, making it not just a practical choice but also an environmentally conscious one.

In conclusion, the Emerson Process Management water dispenser stands out due to its advanced filtration technology, stylish design, user-friendly interface, smart sensors, and energy efficiency. By embracing these features, Emerson continues to lead in providing solutions that enhance convenience and health, making it an ideal choice for modern lifestyles.
Top Page Image Contents