Energy Speaker Systems e:XL-S8, e:XL-S12 manual N e r s m a n u a l, Important Safety Instructions

o w n e r s m a n u a l s u b w o o f e r s

IMPORTANT SAFETY INSTRUCTIONS

Read Instructions

All safety and operating instructions should be read before the product is operated.

Retain Instructions

The safety and operating instructions should be retained for future reference.

Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

Follow Instructions

All operating and use instructions should be followed.

Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

Water and Moisture

Do not use this product near water– for example near a bath tub, wash bowl kitchen sink, or laundry tub; in a wet basement; or near a swimming pool.

Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. They should also never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, please refer to the operating instructions.

Grounding or Polarization

This product may be equipped with a polarized alternating-current line plug (a plug having one blade wide than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. DO NOT defeat the safety purpose of the polarized plug.

Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by the items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

Overloading

Do not overload wall outlets or extension cords, as this can result in a risk of fire or electric shock.

Object and Liquid Entry

Never push objects of any kind in this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards.

Heat

This product should be situated away from heat sources such as radiators ,heat registers, stoves, or other appliances (including amplifiers) that produce heat.

Non-use Periods

The power cord of the product should be unplugged from the outlet when left unused for a long period of time.

Damage Requiring Service

This product should be serviced by qualified service personnel when;

(A)The power supply cord or the plug has been damaged, or

(B)Objects have fallen, or liquid has been spilled into the appliance, or

(C)The product has been exposed to rain, or

(D)The appliance does not operate normally or exhibits a marked change in sonic performance, or

(E)The product has been dropped, or the enclosure has been damaged.

“ENERGY”, the “ENERGY” logo, “Musical Truth”, “e:XL-Series”, the “e:XL Series” logo and “API Accessories” are trademarks of Audio Products International Corp. “Dolby”, “Dolby Pro-Logic” and “Dolby Digital Surround” are trademarks of Dolby Laboratories Licensing. DTS is a Trademark of Digital Theater Systems Inc.

SUBWOOFER CONNECTION TO YOUR AUDIO/VIDEO SYSTEM

There are essentially two methods by which you can connect your Energy subwoofer to your audio/video system. The first is “The High Level Connection” and the second, “The Low Level Connection”. Your system components will dictate which method to use, but High Level Connection can be used with virtually any receiver or amplifier.

In both methods, the left and right channel inputs are combined. That signal is then passed through a variable (50Hz to 100Hz @ 18dB/octave) Low Pass Filter for seamless matching of the subwoofer to the main satellite speakers.

CAUTION: (A) DO NOT USE BOTH LOW LEVEL AND HIGH LEVEL METHODS SIMULTANEOUSLY. (B) TURN OFF ALL POWER IN YOUR STEREO SYSTEM BEFORE PROCEEDING WITH THE INSTALLATION OF THE SUBWOOFER.

Using High Level Connections (see Diagram 1)

On the rear of your Energy subwoofer cabinet is a block designated “High Level”. This block contains two pairs of speaker terminals. These should be connected to the speaker output terminals of your amplifier or A/V receiver. Each pair of terminals are color coded black/red.

NOTE: These terminals will accept up to 18 Gauge speaker wire.

REMEMBER: Always connect red-to-red and black-to-black, when making the connections between amp/receiver to subwoofer. If you inadvertently reverse one of the connections (ie. red-to-black), you will notice a lack of bass from your subwoofer.

Using the “Subwoofer Output” of an A/V Receiver or Processor (See Diag. 2 - Low Level Connection1)

This method uses a single RCA-to-RCA interconnect cable to connect the “SUBWOOFER OUTPUT” jack from your A/V receiver or processor to the subwoofer “INPUT”. This method does not remove low frequencies from your main speakers, and they will continue to reproduce bass frequencies.

Using An External Crossover (See Diag. 3 Low Level Connection 2)

This method uses a single RCA-to-RCA interconnect cable to connect the “SUBWOOFER OUTPUT” jack from an external crossover to the “XOVER INPUT” of your subwoofer. This method by-passes the subwoofer’s built-in level and crossover controls; subwoofer functions are controlled by the external crossover. (See External Crossover Owner’s Manual for details.)

SET UP CALIBRATION

For best results when setting up your system, assume your normal listening position and have another person perform the following adjustments:

1.Set the Subwoofer Level Control to its zero position. Set the Subwoofer LP Filter Control to 50Hz. Set any loudness, bass/treble, and/or equalizer controls on your preamplifier or integrated amp/receiver to their normal or mid-point positions.

2.Play a familiar CD, record, or video soundtrack that has substantial bass content.

3.Gradually turn the Subwoofer Level Control clockwise until you achieve a neutral balance between the subwoofer’s deep bass output and your main/satellite speakers.

4.Slowly turn the Subwoofer LP Filter Control clockwise to reach the best mid bass blend with your main/satellite speakers. This will be the point at which the bass retains solid impact and fullness.

If the mid bass becomes “boomy” or ill defined, you have gone too far and should turn the control counter-clockwiseto the best balance point. If the sound is too thin (i.e., male vocals are not full sounding) then turn the control clockwise to the best balance point.

NOTE: The Subwoofer Level Control is designed to control the balance between your subwoofer and main/satellite speakers and should not be used as a substitute for the bass or loudness controls on your amplifier or receiver. Adjust the subwoofer’s level for smoothest low frequency performance. If more bass is desired, then advance the bass and/or loudness controls on your main amplifier or receiver.

LIMITED WARRANTY POLICY

Warranty Outside of The United States and Canada:

Product warranties may be legislated differently from one country to another. Ask your local dealer for details of the LIMITED WARRANTY applicable in your country.

IMPORTANT: Please retain the carton and packing material for this ENERGY product to protect it in the event it ever has to be shipped to a service center for repair. Product received damaged by a service center that has been shipped by the end user in other than the original packaging, will be repaired, refurbished and properly packaged for return shipment at the end user’s expense.

WARRANTY FOR UNITED STATES AND CANADA (see back cover)

2