o w n e r s m a n u a l

S 8 . 2 / S 1 0 . 2

SET UP CALIBRATION

For best results when setting up your system, assume your normal listening position and have another person perform the following adjustments:

1.Set the Subwoofer Level Control (BL) to its zero position. Set the Subwoofer Low Pass Filter Control (LPF) to its lowest setting (50Hz). Set any loudness, bass/treble, and/or equalizer controls on your Processor or Receiver to their normal or mid-point positions.

2.Play a familiar CD, record, or video soundtrack that has substantial bass content.

3.Gradually turn the Subwoofer Level Control (BL) clockwise until you achieve a neutral balance between the subwoofer’s deep bass output and your main/satellite speakers.

4.Slowly turn the Subwoofer Low Pass Filter Control (LPF) clockwise to reach the best mid bass blend with your main/satellite speakers.This will be the point at which the bass retains solid impact and fullness.

If the mid bass becomes “boomy” or ill defined, you have gone too far and should turn the LPF control counter-clockwise to the best balance point. If the sound is too thin

(i.e., male vocals are not full sounding) then turn the LPF control clockwise to the best balance point.

NOTE:The Subwoofer Level Control is designed to control the balance between your subwoofer and main/satellite speakers and should not be used as a substitute for the bass or loudness controls on your amplifier or receiver. Adjust the subwoofer’s level for smoothest low frequency performance. If more bass is desired, then advance the bass and/or loudness controls on your amplifier or receiver.

SUBWOOFER FEATURES

Auto-On/Auto-Off Circuit

Your subwoofer is equipped with a special “Auto-on/Auto-off ” circuit.This circuit automatically turns your subwoofer on as soon as it senses a program signal. At a predetermined time after the program signal ends, this circuit automatically turns the subwoofer off.

Clipping Protection Circuit

Many powered subwoofers on the market produce distorted sounds as a result of clipping at high input levels.The proprietary ENERGY Clipping Protection Circuit (CPC) continuously senses the input signal level and automatically adjusts to prevent clipping of the waveform, maintaining undistorted bass reproduction.

High Level Input and Output Terminals

The High Level inputs allow you to connect your subwoofer to the speaker outputs of any A/V Receiver or power amplifier.The outputs facilitate easy connection of a set of passive speakers. See “Subwoofer Connection to your Audio/Video System”.

Low-Level RCA Input Jacks

The two RCA Input jacks allow you to connect your subwoofer to EITHER:

1)The subwoofer mono output of an A/V Receiver/Processor OR

2)The subwoofer output of an External Crossover.

NOTE:When using the External Crossover Input, the Subwoofer Level Control (BL) and Low Pass Filter Control (LPF) on the subwoofer’s rear panel are bypassed and have no effect on the subwoofer.

Power Switch

The rear mounted power switch will turn off the AC power to the subwoofer. If you will not be using the subwoofer for extended periods of time, it is recommended to turn the subwoofer off.

SUBWOOFER OPERATING CONTROLS

BL - Subwoofer Level Control

This rotary control adjusts the output level of your ENERGY subwoofer and should be used to balance the level of the subwoofer with that of your main satellite speakers. See “Set-up Calibration”.

LPF - Low Pass Filter Control

This rotary control adjusts the high frequency roll-off of the subwoofer. Continuously variable from 50Hz to 100Hz, it is used to precisely match the subwoofer bass reproduction with that of your main/satellite speakers. See “Set-up Calibration”.

A/V - Audio/Video Switch

This switch is an equalizer that you may use at your discretion. In the Audio position, the equalizer circuit is not engaged. However, in the Video Position, the equalizer is engaged. In the video mode, the equalizer adds more punch to the frequency response, and is usually beneficial during playback of movies. When listening to music, you will probably want to keep this switch in the “Audio” position, however it is completely up to you to decide which position the subwoofer sounds best in.

BL - Volume Control

A/V (Audio/Video)

Switch

LPF - Low Pass Filter

Control

ROOM ACOUSTICS &

SUBWOOFER PLACEMENT

ENERGY subwoofers can be placed virtually anywhere in your listening room without significantly affecting the stereo image of your main speakers. However, interactions between any subwoofer and a room’s acoustic properties will have some impact on the overall bass performance.

Reading this section will help you to find a placement for the subwoofer in your room which will yield the best bass performance.

CAUTION: ENERGY SUBWOOFERS HAVE A BUILT-IN AMPLIFIER AND MUST HAVE ADEQUATE VENTILATION FOR COOLING PURPOSES. DO NOT PLACE THE SUBWOOFER NEAR HEAT SOURCES, OR ANYTHING WHICH MIGHT OBSTRUCT VENTILATION.

Although a clear path between the subwoofer and listening position is not required, it is important to leave approximately 4 inches (10cm) of clearance between the subwoofer and walls or room furnishings.

Generally, shorter runs of hook-up cables are also preferable (and easier to hide), therefore locating your subwoofer relatively close to your audio equipment is often desirable.

The interaction between room acoustics and any subwoofer is closely related to the subwoofer’s proximity to the walls.Typically, subwoofer placement directly in or close to a corner will produce the most bass output, placement along one wall but away from a corner will produce less bass output, and placement of the subwoofer further into the room will produce the least amount of bass output.

It should also be realized that the corner location, although producing the most bass output often yields ill-defined or “boomy” bass.The latter two locations will deliver progressively more accurate bass performance.

We urge you to experiment with various subwoofer placements in your listening room to find the position which produces “deep and smooth” performance. Often, moving the subwoofer a foot or two (30- 60cm) can make a big sonic improvement.

Remember to use familiar musical recordings with an abundance of low frequency information when you experiment with subwoofer locations.

LIMITED WARRANTY POLICY

Warranty Outside of The United States and Canada:

Product warranties may be legislated differently from one country to another. Ask your local dealer for details of the LIMITED WARRANTY applicable in your country.

IMPORTANT: Please retain the carton and packing material for this ENERGY product to protect it in the event it ever has to be shipped to a service center for repair. Product received damaged by a service center that has been shipped by the end user in other than the original packaging, will be repaired, refurbished and properly packaged for return shipment at the end user’s expense.

WARRANTY FOR UNITED STATES AND CANADA (see back cover)

2

Page 3
Image 3
Energy Speaker Systems S10.2 SET UP Calibration, Subwoofer Features, Subwoofer Operating Controls, Limited Warranty Policy

S10.2 specifications

The Energy Speaker Systems S10.2 is a remarkable addition to the world of audio enthusiasts, recognized for its quality, versatility, and impressive performance. This subwoofer is engineered to enhance any audio setup, providing deep, resonant bass that complements a variety of music genres and movie soundtracks alike.

One of the standout features of the S10.2 is its compact yet powerful design. Sporting an efficient 10-inch long-throw woofer, it delivers robust low-frequency response without overwhelming the space it occupies. The woofer is crafted from high-quality materials that ensure durability while optimizing sound clarity and performance.

The S10.2 incorporates advanced technologies that set it apart from other subwoofers in its class. One notable innovation is its intelligent DSP (Digital Signal Processing) control, which allows for precise adjustments and seamless integration with different audio systems. This technology also helps in reducing distortion, preserving audio fidelity even at high volumes.

Another significant feature is the adjustable crossover frequency, enabling users to tailor the subwoofer’s output to the specific characteristics of their main speakers. This customization is crucial for achieving a balanced and cohesive soundstage, enhancing the overall listening experience. Furthermore, the S10.2 includes phase correction circuitry, which optimizes the alignment of sound waves for improved clarity and definition.

The subwoofer is equipped with both line and speaker level inputs, providing versatile connectivity options. This adaptability makes it suitable for various setups, whether it’s a home theater system, a music listening room, or a professional audio installation. Additionally, the S10.2 has a built-in amplifier, delivering powerful performance without the need for an external power source.

Aesthetically, the Energy Speaker Systems S10.2 boasts a sleek and modern design that fits seamlessly into any environment. The durable cabinet construction minimizes vibrations and standing waves, further enhancing audio quality.

In conclusion, the Energy Speaker Systems S10.2 stands out as a well-rounded subwoofer, merging advanced technology with quality design. Its impressive features, including the long-throw woofer, DSP control, adjustable crossover frequency, and versatile connectivity, make it an excellent choice for anyone looking to elevate their audio experience. Whether for casual listening or critical audio applications, the S10.2 delivers, ensuring that users enjoy every note and sound effect with precision and depth.