Enterasys Networks D2G124-12, D2G124-12P set port lacp

set port lacp
4-44 Port Configuration
set port lacp
Usethiscommandtosetlinkaggregationparametersforoneormoreports.Thesesettingswill
determinethespecifiedunderlyingphysicalports’abilitytojoinaLAG,andtheiradministrative
stateonceaggregated.
Syntax
set port lacp port port-string {[aadminkey aadminkey] [aadminstate {lacpactive |
lacptimeout | lacpagg | lacpsync | lacpcollect | lacpdist | lacpdef | lacpexpire}]
[aportpri aportpri] [asyspri asyspri] [enable | [disable] [padminkey padminkey]
[padminport padminport] [padminportpri padminportpri] [padminstate {lacpactive |
lacptimeout | lacpagg | lacpsync | lacpcollect | lacpdist | lacpdef | lacpexpire}]
[padminsysid padminsysid] [padminsyspri padminsyspri]
Parameters
portport‐string Specifiesthephysicalport(s)onwhichtoconfigureLACP.Foradetailed
descriptionofpossibleport‐stringvalues,referto“PortStringSyntaxUsed
intheCLI”onpage4‐1.
aadminkey
aadminkey
Setstheport’sactoradminkey.LACPwillusethisvaluetoformanoper
keyandwilldeterminewhichunderlyingphysicalportsarecapableof
aggregatingbycomparingoperkeys.Aggregatorportsallowonly
underlyingportswithoperkeysmatchingtheirstojointheirLAG.Valid 
valuesare1‐65535.Thedefaultkeyval ueis32768.
aadminstate
lacpactive|
lacptimeout|
lacpagg|lacpsync
|lacpcollect|
lacpdist|lacpdef|
lacpexpire
Setstheport’sactorLACPadministrativestatetoallowfor:
lacpactive‐Tran smi tti ngLACPPDUs.
lacptimeout‐TransmittingLACPPDUsevery1sec.vs30sec.(default).
lacpagg‐Aggregationonthisport.
lacpsync‐Tran sit ion tosynchronizationstate.
lacpcollect‐Tran sit ion tocollectionstate.
lacpdist‐Tran siti ontodistributionstate.
lacpdef‐Tran sit ion todefaultedstate.
lacpexpire‐Tran sit ion toexpiredstate.
aportpriaportpri Setstheport’sactorportpriority.Vali dvalues are0‐65535,withlower
valuesdesignatinghigherpriority.
asyspriasyspri Setstheport’sactorsystempriority.TheLACPimplementationontheD‐
Seriesdeviceusesthisvaluetodetermineaggregationprecedencewhen
therearetwodevicescompetingforthesameaggregator.Valid valuesare
0‐65535,withhigherprecedencegiventolowervalues.
Note: Only one LACP system priority can be set on a D-Series
device, using either this command, or the set lacp asyspri command
(“set lacp asyspri” on page 4-38).
enable (Optional)EnablesLACPDUprocessingonthisport.
disable (Optional)DisablesLACPDUprocessingonthisport.
padminkey
padminkey
Setsadefaultvaluetouseastheport’spartneradminkey.Onlyports
withmatchingadminkeysareallowedtoaggregate.Vali dvalues are1‐
65535.