Installation

SLIDER/DAMPER SET-UP:

This is used to regulate the airflow through the pellet stove. The slider Damper has been factory set for German test pellet fuel.

 

The

slider

damper

is

 

located

behind

the

left

 

side panel. To open the

Air Intake Box

left side panel, undo the

one screw located in the

Exhaust Channel

upper front corner of the

Slider Damper

cabinet

side

between

Exhaust Blower

the louvers. Also loosen

three screws down the

 

back of the side panel.

Figure 29: Slider/Damper Plate in Unit.

The combustion exhaust blower is a variable speed blower controlled by the heat output button. This blower will decrease the vacuum pressure inside the stove and as the heat output button is turned down. The vacuum pressure inside the firebox will increase as the combustion exhaust blower increases in speed (higher heat output setting).

If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly, decreasing the air in the firebox.

If, after long periods of burning, the fire builds up and overflows the burn pot or there is a build up of clinkers, this would be a sign that the pellet quality is poor, this requires more primary air, the slider damper must be pulled out to compensate. Pulling the slider damper out gives the fire more air.

The easiest way to make sure that an efficient flame is achieved is to understand the characteristics of the fire.

•A tall, lazy flame with dark orange tips requires more air – Open slider (pull out) slightly.

•A short, brisk flame, like a blowtorch, has too much air – Close slider (push in) slightly.

•If the flame is in the middle of these two characteristics with a bright yellow/orange, active flame with no black tips then the air is set for proper operation.

SPECIAL NOTES:

Pellet quality is a major factor in how the Pellet stove will operate. If the pellets have a high moisture content or ash content the fire will be less efficient and has a higher possibility of the fire building up and creating clinkers (hard ash build-up).

Taking a reading of vacuum pressure inside the firebox with a magnehelic gauge can be used to set the slider for best combustion. The best settings are a reading of approximately 0.10 inches of water column on the high fire setting. Some fuels may require higher or lower settings. The reading can be taken from the 1⁄8” (3 mm) hole located on the front of the unit below the door and behind the magnetic ash lip.

26

Page 25 Page 27
Page 26
Image 26
Enviro C-10608 owner manual Slider Damper Located Behind Left Side panel. To open, Special Notes
Page 25 Page 27

C-10608 specifications

Enviro C-10608 is an innovative solution designed to address the increasing environmental concerns related to chemical waste management and pollution control. Leveraging state-of-the-art technologies and advanced material science, Enviro C-10608 provides a comprehensive approach to minimizing the ecological footprint of industrial operations.

One of the main features of Enviro C-10608 is its exceptional versatility. It can be utilized across various sectors, including manufacturing, oil and gas, and agriculture. This adaptability makes it a valuable asset for organizations looking to comply with stringent environmental regulations while improving their sustainability practices. By effectively treating and managing waste materials, Enviro C-10608 promotes circular economy principles and helps companies reduce their reliance on raw materials.

Moreover, Enviro C-10608 employs cutting-edge filtration technologies that enhance its performance significantly. Its advanced filtration system is designed to capture a wide range of contaminants, including heavy metals, toxins, and organic compounds, ensuring that discharged effluents meet or exceed environmental standards. This not only protects local ecosystems but also safeguards public health, making it an essential tool in modern waste management.

Another notable characteristic of Enviro C-10608 is its low energy consumption. The product is engineered to operate efficiently, reducing the overall carbon footprint associated with waste treatment processes. This energy efficiency is further complemented by its use of renewable energy sources, further enhancing its appeal to environmentally conscious organizations.

Additionally, Enviro C-10608 features real-time monitoring and reporting capabilities. This technological integration allows for the continuous assessment of treatment efficiency and compliance levels, ensuring that users can make informed decisions based on accurate data. The user-friendly interface simplifies the monitoring process, enabling companies to adapt their operations swiftly in response to changing environmental regulations.

Finally, Enviro C-10608 stands out for its commitment to safety and user-friendliness. Designed with straightforward installation and operation procedures, it minimizes downtime and training requirements for staff. The product’s materials are non-toxic and sustainable, promoting a healthier work environment.

In conclusion, Enviro C-10608 embodies a forward-thinking approach to waste management. With its versatile applications, advanced filtration technologies, energy efficiency, real-time monitoring, and commitment to safety, it is poised to become a cornerstone in the sustainable practices of industries worldwide.
Top Page Image Contents