Installation

SLIDER/DAMPER SET-UP:

This is used to regulate the airflow through the pellet stove. The slider damper should be set by a trained

technician using magnehelic.

The slider damper is located

 

 

behind the left side panel. To

 

open the left side panel, undo the

 

one screw located in the upper

 

front corner of the cabinet side

 

between the louvers. Also loosen

 

three screws down the back of

Air Intake Box

the side panel.

 

 

 

 

 

Slider Damper

The combustion exhaust blower is

 

a variable speed blower controlled

Exhaust Channel

by the heat output button. This

Exhaust Blower

blower will decrease the vacuum

pressure inside the stove and as

 

 

the heat output button is turned

 

down.

The

vacuum

pressure

 

inside the firebox will increase as

 

the combustion exhaust blower

 

increases in speed (higher heat

Figure 28: Slider/Damper Plate in Unit.

output setting).

 

 

 

 

 

If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly, decreasing the air in the firebox.

If, after long periods of burning, the fire builds up and overflows the burn pot or there is a build up of clinkers, this would be a sign that the pellet quality is poor, this requires more primary air, the slider damper must be pulled out to compensate. Pulling the slider damper out gives the fire more air.

The easiest way to make sure that an efficient flame is achieved is to understand the characteristics of the fire.

•A tall, lazy flame with dark orange tips requires more air – Open slider (pull out) slightly.

•A short, brisk flame, like a blowtorch, has too much air – Close slider (push in) slightly.

•If the flame is in the middle of these two characteristics with a bright yellow/orange, active flame with no black tips then the air is set for proper operation.

SPECIAL NOTES:

Pellet quality is a major factor in how the Pellet stove will operate. If the pellets have a high moisture content or ash content the fire will be less efficient and has a higher possibility of the fire building up and creating clinkers (hard ash build-up).

IMPORTANT: Taking a reading of vacuum pressure inside the firebox with a magnehelic gauge should be used to set the slider for best combustion. The best settings are a reading of approximately

0.11- 0.12 inches of water column (27 - 30 Pa) on the high fire setting. Some fuels may require higher or lower settings. The reading can be taken from the 1⁄8” (3 mm) hole located on the front of the unit below the ash shelf.

19

Page 18 Page 20
Page 19
Image 19
Enviro C-10985 technical manual Special Notes
Page 18 Page 20

C-10985 specifications

Enviro C-10985 is a cutting-edge environmentally friendly chemical formulation specifically designed for industrial cleaning and degreasing applications. Its introduction marks a significant advancement in sustainable chemical solutions, catering to industries that prioritize safety and environmental impact.

One of the main features of Enviro C-10985 is its non-toxic composition. Unlike traditional solvents that often contain hazardous volatile organic compounds (VOCs), this innovative formula is derived from renewable sources, making it safe for users and the environment. The low-VOC content minimizes air pollution and reduces health risks associated with exposure to harmful chemicals, aligning with stringent safety regulations and guidelines.

The technology behind Enviro C-10985 incorporates advanced surfactant systems that enhance its cleaning efficacy. These surfactants are designed to penetrate and lift grease, oil, and dirt from various surfaces. The product can be employed on metals, plastics, and other materials, ensuring versatility in industrial applications. The biodegradable nature of these surfactants further emphasizes the product's eco-friendliness, as it breaks down without leaving harmful residues.

Enviro C-10985 is also formulated to be user-friendly. It comes in a concentrated solution that can be diluted to meet the specific needs of various cleaning tasks, reducing both waste and transportation costs. The product’s formulation is compatible with various application methods, including pressure washing, spray application, and manual cleaning, making it suitable for a wide range of operational contexts.

Another characteristic of Enviro C-10985 is its performance at varying temperatures. It retains its cleaning power in both cold and hot water, making it adaptable to different cleaning scenarios. This feature is particularly beneficial in industries where temperature controls vary significantly.

Additionally, Enviro C-10985 is designed to mitigate corrosion and protect surfaces during the cleaning process, contributing to the longevity of equipment and machinery. The formulation includes corrosion inhibitors that safeguard metal surfaces from rust and degradation, ensuring consistent performance over time.

In conclusion, Enviro C-10985 is an exemplary solution for businesses seeking effective, safe, and environmentally responsible cleaning products. Its unique features, advanced technology, and compatibility with multiple applications make it an invaluable asset in modern industrial cleaning regimes.
Top Page Image Contents