TROUBLESHOOTING

DO NOT:

-Hold the start-up switch down, this is a momentary contact switch and can be damaged if held down too long.

-Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures.

-Remove any screws in the firebox without first lubricating them with penetrating oil.

TROUBLESHOOTING:

What to do if:

1.The stove will not start

2.The stove will not operate when hot

3.The exhaust blower will not function

4.The convection blower will not function normally

5.Igniter , The pellets will not light.

6.The auger motor does not function normally

7.The Dial-A-Fire has no effect on the fire

8.The stove will not shut off

9.The stove keeps going out

*NOTE: All troubleshooting procedures should be carried out by qualified technicians.

1.The stove will not start

-Make sure the stove is plugged in and the wall outlet is supplying power.

-Push the Start-up switch, if the stove fails to start, unplug the unit and open the hinged side panels (held tight with two screws).

-With the stove unplugged, examine all connections. Make sure they are firmly connected and that there are no exposed wires touching the stove (except the chassis ground wire).

-Check the continuity and placement of connections against the diagram in the back of this manual.

-Ensure that the connections to the (15) minute start-up timer are correct.

-Attempt to bypass the switch by inserting a jumper wire between the red and white wires that attach to the switch. Plug the stove back in. If the stove starts, replace the switch.

-If this fails, replace the (15) minute start-up timer.

2.The stove will not operate when hot

-Unplug the stove, open the left side panel. Jump the two brown leads that are attached to the 140°F (60°C) temperature sensor. If the stove operates replace the 140°F (60°C) sensor.

3.The exhaust motor will not function normally

-Open the left side panel, check all connections against the wiring diagram.

-If all the connections are verified and the exhaust blower does not function at all, tap lightly on the exhaust blower’s motor end cap, this may loosen a tight motor.

-Apply 115 V directly to the exhaust blower. If the motor does not run, replace the blower.

-If the motor runs, have your dealer check the harness.

24

Page 23 Page 25
Page 24
Image 24
Enviro FS, FPI, BIH technical manual Troubleshooting, Do not
Page 23 Page 25

BIH, FS, FPI specifications

Enviro FPI, FS, and BIH are innovative technologies that have significantly contributed to the field of environmental protection and sustainability. These systems are designed to address various environmental challenges by utilizing advanced features and methodologies that promote efficiency and effectiveness.

The Enviro FPI (Floating Photovoltaic Installation) is a groundbreaking technology that involves the installation of solar panels on bodies of water. This approach not only generates renewable energy but also minimizes land use, which is critical in densely populated areas. The floating structure reduces water evaporation and helps maintain water quality by limiting algae growth. Additionally, the cooling effect of water can enhance the efficiency of solar panels, resulting in higher energy output.

The Enviro FS (Floating System) expands upon the principles of FPI by integrating multiple environmental functionalities. This system includes features such as water filtration and oxygenation, which are essential for improving aquatic ecosystems. The incorporation of bioremediation technologies allows for the natural degradation of pollutants, making it a multifunctional solution for water bodies facing contamination. The FS system is engineered to blend seamlessly into its environment, ensuring minimal disruption to local wildlife and habitats.

The Enviro BIH (Biodegradable Industrial Hemp) represents a leap forward in sustainable materials. Utilizing industrial hemp, this technology creates biodegradable products that can replace conventional plastics. Hemp is known for its fast growth rate and low environmental impact, making it a viable alternative for various industries. The use of BIH not only helps reduce plastic waste but also supports sustainable agriculture and provides economic opportunities for farmers.

All three technologies embody key characteristics that make them stand out in the field of environmental innovation. They are designed with sustainability at their core, emphasizing the importance of balancing human activity with ecological preservation. The integration of renewable energy generation, pollution remediation, and the use of biodegradable materials showcases a holistic approach to modern environmental challenges.

Furthermore, these technologies are scalable and adaptable, allowing for implementation in various contexts, from urban settings to rural areas. As awareness of environmental issues continues to grow, solutions like Enviro FPI, FS, and BIH play an essential role in promoting a greener and more sustainable future for generations to come. Through their combined efforts, these technologies pave the way toward a more responsible relationship with our planet.
Top Page Image Contents