Epson 6200A INC Mn , HALT

Source Format:

Operation:

OP-Code:

Type:

Clock Cycles:

Flag:

Description:

Example:

Source Format:

Operation:

OP-Code:

Type:

Clock Cycles:

Flag:

Description:

Example:

MSB LSB

MSB LSB

C–

Z–

D–

I–

C–

Z–

D–

I–

S1C6200/6200A CORE CPU MANUAL EPSON 41

3 INSTRUCTION SET

INC Mn Increment memory by 1

HALT Halt

HALT

Stops CPU

111111111000 FF8H

VI

5

Not affected

Not affected

Not affected

Not affected

Stops the CPU. When an interrupt occurs, PCP and PCS are pushed onto the

stack as the return address and the interrupt service routine is executed.

Instruction State PCP PCS I flag

HALT RUN 0001 0011 0011 1

HALT

Interrupt 0001 0011 0100 1

RUN 0001 Interrupt vector address 0

INC Mn

M(n3 to n0) ← M(n3 to n0) + 1

11110110n

3n2n1n0F60H to F6FH

IV

7

Set if a carry is generated; otherwise, reset.

Set if the result is zero; otherwise, reset.

Not affected

Not affected

The contents of the data memory location addressed by Mn is incremented by 1.

INC M1 INC M3 INC M0DH

Memory (01H) 0100 0101 0101 0101

Memory (03H) 1111 1111 0000 0000

Memory (0DH) 0111 0111 0111 1000

C flag 0 0 1 0

Z flag 1 0 1 0

Contents

Main NOTICE SEIKO EPSON CORPORATION 2001, All rights reserved. Configuration of product number Devices S1 C 60N01 F 0A01 Development tools S5U1 C 60R08 D1 1 00 Page S1C6200/6200A Core CPU Manual CONTENTS 1D 2M 3I B. INSTRUCTION INDEX ______________________________________ 87 Page 1D 1.1 System Features 1.2 Instruction Set Features 1.3 Differences between S1C6200 and S1C6200A 1 DESCRIPTION S1C6200 CORE CPU 8-bit address bus13-bit address bus Fig. 1.1 Block diagram 4-bit data bus S1C6200/6200A CORE CPU MANUAL EPSON 3 2M Fig. 2.1.1 Program memory configuration (within bank) PCB (between banks) 2.1 Program Memory (ROM) 2.1.1 Program counter block 2.1.2 Flags 2.1.3 Jump instructions 2.1.4 PSET with jump instructions 2.1.5 Call instructions 2.1.6 PSET instruction 2.1.7 CALZ instruction Fig. 2.1.7.1 The use of the CALZ instruction Bank 0 Page 0 EEE.................... RET 2.1.8 RET and RETS instructions Bank 0 Page 0 Program memory PSET CALL LD LD Bank 0 Page 10 Program memory DDD.................... RET RETS 2.2 Data Memory (within page) (page specification) 4-bit data Memory or I/O Register area Index register IY Stack pointer SP Register pointer RP 2.3 ALU (Arithmetic Logic Unit) and Registers Operation Instruction ADD ADC SUB SBC AND OR XOR CP FAN RRC RLC NOT 2.3.1 D (decimal) flag and decimal operations 2.3.2 A and B registers 2.4 Timing Generator 5-clock/7-clock instructions 12-clock instructions 2.4.1 HALT and SLP (sleep) modes 2.5 Interrupts 2.5.1 Interrupt vectors 2.5.2 I (interrupt) flag 2.5.3 Operation during interrupt generation Fig. 2.5.3.1 Interrupt timing during execution S1C6200/6200A CORE CPU MANUAL EPSON 13 S1C6200 S1C6200A Fig. 2.5.3.2 Interrupt timing in the HALT mode Fig. 2.5.3.3 Interrupt timing in SLEEP mode Fig. 2.5.3.4 Interrupt timing with PSET System clock CPU clock Status Instruction S1C6200/6200A S1C6200 2.5.4 Initial reset On reset, the registers and flags are set as shown in Table 2.5.4.1. Table 2.5.4.1 Reset value 3I 3.1 Instruction Indices a. Index by function b. Index in alphabetical order c. Index by operation code 3.1.1 By function Page Page 3.1.2 In alphabetical order Page Page 3.1.3 By operation code Page Page 3.2 Operands n n 3.3 Flags 1. Carry flag 3.4 Instruction Types (I) (II) (III) (IV) ACPX MX,r ACPY MY,r ADC r,i ADC r,q ADC XH,i ADC XL,i ADC YH,i ADC YL,i ADD r,i ADD r,q AND r,i AND r,q CALL s CALZ s CP r,i CP r,q CP XH,i CP XL,i CP YH,i CP YL,i DEC Mn DEC SP Decrement memory DI EI FAN r,i FAN r,q INC Mn HALT Increment stack pointer by 1INC SP INC X INC Y JPBA JP C,s JP NC,s JP NZ,s JP s JP Z,s LBPX MX,e LD A,Mn LD B,Mn LD Mn,A LD Mn,B LDPX MX,i LDPX r,q LDPY MY,i LDPY r,q LD r,i LD r,q LD r,SPH LD r,SPL LD r,XH LD r,XL LD r,XP LD r,YH LD r,YL LD r,YP LD SPH,r LD SPL,r LD X,e LD XH,r LD XL,r LD XP,r LD Y,e LD YH,r LD YL,r LD YP,r NOP5 NOP7 NOT r OR r,i OR r,q POP F POP r POP XH = XH POP XL = XL POP XP POP YH = YH POP YL POP YP = YP PSET p PUSH F PUSH r = r-register PUSH XH PUSH XL PUSH XP PUSH YH PUSH YL PUSH YP = YP RCF RDF RET RETD e Load immediate data e to memory, and increment X by 2, then return RETS RLC r RRC r r-register C RST F,i Cd r-register CC RZF SBC r,i SBC r,q SCF SCPX MX,r SCPY MY,r SDF SET F,i SLP SUB r,q SZF XOR r,i XOR r,q ABBREVIATIONS APPENDIX A. S1C6200A (ADVANCED S1C6200) CORE CPU A1 Outline of Differences A2 Detailed Description of the Differences A2.1 Initial reset A2.2 Interrupt Operation during interrupt issuance b) At HALT mode c) During "PSET" instruction execution Fig. A2.2.1 Timing chart of S1C6200A interrupt a) During instruction execution Clock Status Instruction System clock CPU clock Status Instruction <Reference 1> Writing on the interrupt mask register during EI <Reference 2> Reading the interrupt factor flag during EI Page L N O P P R S X International Sales Operations AMERICA EUROPE ASIA