Epson MTX 1345 manual Standard Configuration, Recall Factory, Dtr

Configuring the printer

3.2Standard Configuration

The standard configuration is reflected in the following printout provided that no

parameters have been changed.

PRINT OUT		VERSION		202xxxxx
INTERFACE		ADJUSTMENT
BUFFER	8 KBYTE	AGC POSITION		24
WORD LENGTH	8 BIT	PLATEN GAP		0
I/F TYPE	SHARED	PAPER-IN ADJ.		0	*)
BAUD-RATE	9600 BPS	CUT. V-POS		0
PARITY BIT	EVEN	UNI-DIRECT.CMD		YES
PROTOCOL	DTR	TRACT. FF-MODE		IGNORE FF
AUTO-STATUS	NO
		MENU ACCESS		ALL FUNCTIONS
CURRENT SETTINGS		MACRO 1	MACRO 2	MACRO 3	MACRO 4*
FONT	DATA	DATA	DATA	DATA	DATA
PRINT QUALITY	LQ	LQ	LQ	LQ	LQ
SUB/SUPER FONT	YES	YES	YES	YES	YES
PITCH	10 CPI	10 CPI	10 CPI	10 CPI	10 CPI
LINE	6 LPI	6 LPI	6 LPI	6 LPI	6 LPI
PAGE LENGTH	72 LINES	72 LINES	72 LINES	72 LINES	72 LINES
TRACTOR V-POS	0	0	0	0	0
MANUAL V-POS	0	0	0	0	0
BIN 1 V-POS	0	0	0	0	0
BIN 2 V-POS	0	0	0	0	0
BIN 3 V-POS	0	0	0	0	0
LEFT MARGIN	1 COLUMNS	1 COLUMNS	1 COLUMNS	1 COLUMNS	1 COLUMNS
RIGHT MARGIN	136 COLUMNS	136 COLUMNS	136 COLUMNS	136 COLUMNS	136 COLUMNS
TOP MARGIN	1 LINES	1 LINES	1 LINES	1 LINES	1 LINES
BOTTOM MARGIN	1 LINES	1 LINES	1 LINES	1 LINES	1 LINES
PERF. SKIP	YES	YES	YES	YES	YES
PAPER SOURCE	TRACTOR	TRACTOR	TRACTOR	TRACTOR	TRACTOR
PAPIER EXIT	STACKER	STACKER	STACKER	STACKER	STACKER
EMULATION	EPSON LQ	PHILIPS GP	IBM PROPR.	IBM PROPR. AGM	EPSON LQ
CHARACTER SET	EPSON EXT.GCT	NV-2.5	IBM SET 2	IBM SET 2	EPSON EXT. GCT
	1: U.S.A.	1: D -NV 2.5	1: U.S.A.	1: U.S.A.	1: U.S.A.
LINE MODE	LF=LF, CR=CR	LF=LF, CR=CR	LF=LF, CR=CR	LF=LF, CR=CR	LF=LF, CR=CR
$$-COMMAND	NO	NO	NO	NO	NO
TEAR-OFF-MODE	NO	NO	NO	NO	NO
PRE-SEPARATION	NO	NO	NO	NO	NO

Note: An asterisk (’) indicates the actual macro.

*) This value is dependent on factory setting!

All this standard settings of the firmware will be restored with the menu function

RECALL FACTORY.

Configuring the printer

3.3Explanation of the printout on the previous page

The heading PRINT OUT gives information about the VERSION of the printer's firmware.

The next two headings are followed by two columns of standard settings:

-INTERFACE - for communication between the computer operating system and the printer it is necessary to have the same communication settings or features. The standard settings are:

-	Buffer	8 KByte
-	Word Length	8 Bit
-	I/F Type	Shared
-	Baud Rate	9600 Bps
-	Parity Bit	Even
-	Protocol	DTR
-	Auto-Status	No

-ADJUSTMENT - all parameters are for adjustment of the printer and the paper (see also the following pages).

The last part of the printout is a list with all MACRO settings. In this case MACRO 4 is marked with an asterisk (’) which identifies it as the active macro.

If you make modifications in the active macro without saving them you will find the new settings under the heading CURRENT SETTINGS. Unless they are saved, the modifications will stay active only until the printer is switched off in which case the macro settings marked with the asterisk will be reactivated.

3-33-4