Epson TM-T60/T60P, TM-T80/T80P Formula

The foIlowing shows an example program used when the drawer connected to

the drawer drive signal 1 is driven using an ON time of 200 ms.

PRINT #1, CHR$(&H1B);“P”;CHR$(0);CHR$

GOSUB*WAlT3OOMS

*WAlT3OOMS

ON time 200ms OFF time 500ms

300[ms] wait routine (* NOTE)

RETURN

NOTE: *This part is indicated in Formula D-3. Set this value so that it

can satisfy

Formula

D-3 (or provides an internal processing time

at least as long as the wait routine time.)

When the drawer is driven according to the conditions above, the drive

waveform is as shown in Figure D-2.

Figure D-2. Example Drawer Drive Signal Waveform

-73-

Contents

Main NOTICE: FCC-CLASS A FCC COMPLIANCE STATEMENT FOR AMERICAN USERS WARNING FOR CANADIAN USERS INTRODUCTION . Four-way I About this manual CONTENTS Page Page Chapter 1 Unpacking the Printer 1 - 1 Checking the Contents of the Box 1-2 Choosing a Place for the Printer 1-3 Removing the Protective Material 1-4 Names and Functions of Parts n Part names -5- Chapter 2 Before Setting Up 2- 1 Connecting the Power Supply to the Printer 2-2 Connecting the Host Computer to the Printer TM-T60P/T80P procedure. Chapter 3 Installing the Parts 3-l Installing the Roll Paper Chapter 3 Installing the Parts 3-l Installing the Roll Paper Page Page 3 -2 Adjusting the Paper-End Detector Page 3 -3 Setting the DIP Switches 1200 bps 9600 ONOFF 19200 OFFOFF Page Chapter 4 The Self Test 4 - 1 The Open-Cover Detector 4 -2 Checking Operation with the Self Test - 18- Page Chapter 5 Cautions while Using the Printer 5-l Function I Panel Switches and Commands 5-2 Printable Area -21- 5 -3 Miscellaneous Notes Page Page 5 - 4 Error Correction Lights: Impossible to recover inspected.) head 300 5-5 Cleaning the Head -27- Chapter 6 Software Control 6 - 1 Printer Control HT 6 - 2 Command Descriptions *XXX *[Range *[Description] *Example 6 - 3 Commands HT < 09 > -30- ESC D LF ESC SP nSet character right-side spacing ESC ! n ESC % n ESC & s n m [a[p]sXa]m-n+1 s = 3 Page ESC * m n1 n2 [d]k Set bit image mode k = (n1 + 256 x n2) X 3 (m = 32, 33) 24-dot double-density Page ESC 2 Set 1/6 inch line spacing ESC 3 Set line spacing using minimum units n = 60 (1/6 inch) ESC J n ESC R n Country -38- Bit Country ESC c4 n Select paper detectors to stop printing -39- Selects the paper detectors used to stop printing. Value ESC d nPrint and feed paper n lines Not defined. ESC p m n1 n2 Generate pulse ESC t n Select character code table n = 0 ESC v Transmit printer status ESC u n ESC { n When upside-down char- ESC V n Set/channel 90 cw(clockwise) rotated characters ESC $ n1 n2 ESC n1 n2 - Any specification exceeding the printable area will be ignored. ESC $ GS k n [d]k NUL Selects a bar code system and prints the bar code. GS w n Selects the horizontal size of the bar code. n = 3 -45- GS h n Select height of bar code n = 162 GS H n Select printing position of HRI characters GS GS / GS / m Not defined. GS * GS : Set starting/ending, position of macro definition Specifies the starting or ending position of the macro definition. GS ^ n1 n2 n3 Not defined. GS : I ESC = n -50- 2 ESC a n 6 - 4 Program Descriptions TM-T60/T80 "CHR$(27)" 100 OPEN "COM1:N81NN" #1 120 PRINT #1, ABCDEF ;CHR$(1O); 130 PRINT #1, CHR$(27); ! ;CHR$(1); 140 PRINT #1, ABCDEF ;CHR$(10); Page Page Page -57- can status List ******** MS-DOS BASIC HOST COMPUTER:EPSON PC-286 APPENDIX APPENDIX A General Specifications Page Page Page APPENDIX B Connectors Page (3) during APPENDIX C Interfaces (a) 2. Interface connector terminal assignments and signal functions -68- Page Page Page Page Formula Page Page Page APPENDIX F Command Summary