* If a stand is already attached to

*

 

*

 

 

 

your display, remove it according

 

 

 

 

 

 

to display manufacturer directions.

 

 

 

 

 

 

Place the display on a clean, flat,

 

 

 

 

 

 

padded surface or, if you prefer, lean

 

 

 

 

 

 

the displ ay against a stable, vertical

 

 

 

 

 

 

surface.

 

 

1

 

 

 

 

 

 

 

 

 

1

1

 

 

 

 

 

 

 





 

 

 

Choosing Display Bracket

 

 

 

 

 

 

Fasteners

 

 



 

 

 

Notice that several sizes of screws



 

 

 

 

 

and spacers have been provided

 

 

 

 

 

 

for mounting the Tilt Mount

 

 



 

 

brackets to your large display.

 

 



 

 

 

The instructions and illustrations

 

 

a

 

 

 

in this Reference Guide will help

 

 

 



you establish the appropriate

 

 

 

 

 

combination of fasteners based

 

 

 

 

 

 

on the depth and diameter of the

 



 

 

 

 

mounting holes at the back of your

 



 

 

 

 

display, along with the design of

 

 

 

 

 

 

the area surrounding the mount-

 

 

 

 

 

 

ing holes (Flat, Curved or Inset).

a

 

b

 

 

 

a Display Style



 

 

 

 

 



 

 

 

The design of the back of your

 

 



 



PP 

display (flat, curved, inset) along

 

 

PP

PP

PP

 

with the diameter and depth of

 

 

 

 

 

 

the mounting holes at the back of

 

 

 

 

 

 

your display will determine which

 

 

 

 

 

 

combination of hardware you will

 

 

 

 

 

 

use to attach the display bracket

 

 



$

PP

PP

to your display. Look at the back

 

 

 

 

% PP

PP

of your display to see if the surface

b

 



 

 

 

surrounding the mounting holes is

 

 

 

 

 

Flat, Curved or Inset.



 

OO

 

 

 

b Hole Diameter

OO OO

OO 

c

 

 

 





 

 

 

 

Four sets of display bracket screws

 

 

 

 

 

 

have been provided, each of a dif-

 

 

 

 

 

 

ferent diameter: 4mm, 5mm, 6mm,

 

 

 

 

 

 

and 8mm. Compare the screws

#

OO

OO

 

 

 

with the diameter of the mounting

 

 

$

 

 

 

holes at the back of your display to

OO

OO

 

 

 

 

find the same size. NOTE: Washer

 

 

 

 

 

 

A is provided for use with the 4mm

c

 

 

 

 

 

and 5mm screws while Washer B



 

 

 

 

works with 6mm and 8mm screws.

 

 

 

 

 

c Hole Depth

 

 

 

 

 

 

Lay the display bracket over the

 

 

 

 

 

 

display mounting holes and

 

 

 

 

 

 

measure the depth of the display

 

 

 

 

 

 

mounting holes with a slender

 

 

 

 

 

 

stick.

 

 

 

 

 

 

888-60-182P-01 rev.D • 01/07

5 of 22