Estate TUD6750 Canceling a Cycle, Changing a Cycle or Setting, Adding Items During a Cycle, Light

Normal

Use this cycle for loads with normal amounts of food soil. (The energy-usage label is based on this cycle.)

Use covered detergent dispenser section.

Wash	Main	Rinse or	Final	Dry	Approximate	Water
	Wash	Purge	Rinse		Time	Usage
						(gal/L)
		●	●	●	1.5 hrs*	4.6/17.4
		Purge

Light

Use this cycle for prerinsed or lightly soiled loads.

Use covered detergent dispenser section.

Wash	Main	Rinse or	Final	Dry	Approximate	Water Usage
	Wash	Purge	Rinse		Time	(gal/L)
		●	●	●	1.5 hrs*	4.8/18.2
		Purge		cycled

Rinse & Hold

Use this rinse cycle for rinsing dishes, glasses, and silverware that will not be washed right away.

Do not use detergent with this cycle.

Wash	Main	Rinse or	Final	Dry	Time (min)	Water
	Wash	Purge	Rinse			Usage
						(gal/L)
		●			10	2.2/8.3
		Rinse

Canceling a Cycle

1.Press CANCEL/DRAIN. The Cancel/Drain light glows.

2.The dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. The light turns off after

2 minutes. The door must be closed for the dishwasher to drain.

To stop the drain

You can press CANCEL/DRAIN again to stop the drain. Be sure to drain the dishwasher before starting a new cycle.

Changing a Cycle or Setting

You can change a cycle anytime during a cycle.

1.Lift the door latch to stop the cycle.

2.Select a new cycle and/or options.

3.Check the detergent dispensers. They must be filled properly for the new cycle.

4.Close the door firmly until it latches. Press START/RESUME. The dishwasher starts a new cycle.

Adding Items During a Cycle

You can add an item anytime before the main wash starts, or the cycle control knob reaches Normal Wash.

1.Lift up the door latch to stop the cycle. Wait for the spraying action to stop before opening the door.

2.Open the door and add the item.

3.Close the door, but do not latch it. Wait 30 seconds for the air in the dishwasher to warm up. This reduces the amount of moisture escaping from the vent when restarting a cycle.

4.Close the door firmly until it latches. Press START/RESUME. The dishwasher resumes the cycle.

Option Selections

You can customize your cycles by pressing an option. If you change your mind, press the option again to turn the option off. Select a different option if desired.

You can change an option anytime before the selected option begins. For example, you can press an unheated drying option anytime before drying begins.

After a wash cycle, the dishwasher remembers the options used and uses the same options in the next wash cycle, unless you select new options.

Hi-Temp Wash

Select this option to heat the water to 140°F (60°C) in the main wash. This option adds heat and wash time. Heating the water helps improve washing results.

NOTE: The Pots & Pans cycle automatically uses this option. Hi- Temp Wash is an option with the Heavy and Normal wash cycles. This option does not work with the Light wash cycle.

Heated Dry

The Heated Dry option in combination with rinse aid will give you excellent drying results. The energy to use Heated Dry costs pennies per cycle. Heated Dry is on when the light is lit on the Heated Dry button. Be sure to load plastic items in the upper rack to avoid damage. You may turn off the Heated Dry option by pressing HEATED DRY so that the light goes off. However, you will have items in your dish load that will not be dry at the end of the cycle.

NOTE: The Heated Dry option is used in all cycles except Quick Rinse.

10