Eureka! Tents Copper Canyon 10 manual Roof poles Wall poles

ASSEMBLY INSTRUCTIONS

For the Copper Canyon 10

Component List:

1 Tent Body with Guy Ropes, 4 Wall Poles, 2 Roof Poles, 2 Fly Poles, 1 Fly, 1 Carry Bag, 1 Stake Bag and Stakes, 1 Pole Bag

1.Remove from the carry bag and separate all the components. Unroll and unfold the fabric top side up, on a clean, dry space and open the doors. If windy, stake down the windward corner. See fig 1.

fig 1

4. Raise the tent. Start on one side and insert the wall poles into the the elbows. At the bottom of each pole, insert the pin/ring (attached to the corner web) into the

bottom of each pole. See fig 5. Repeat on the other side until the

tent is at full height and freestanding.

fig 5

5. Attach all clips to the wall poles. See fig 6.

Stake the tent down through the corner web loops. Stake opposite corners while applying tension to smooth the floor wrinkles. It works best to do this before you add the fly. See fig 7.

fig 6

7.Attach the fly to the tent. Turn the fly assembly over and align it so that the fly pole ends point to the doors. Grasp the corners of the of the fly and drag them up and over the roof poles to completely cover the roof. ( This is much easier with two people. ) The end of the poles should point out over the doors.

At the corners of the tent, reach under the fly and attach
the hook & loop straps to the wall poles just below the
elbow and down the length of the wall poles, securing
the fly in place. See fig 11.
At the bottom/corners of the tent, attach the
shockcorded J-hooks to the nylon rings on the corner	fig.11
web loops. See fig 12.
8. Stake out the attached guy ropes and adjust
tension with the in-line sliders. See fig 13.

YOUR TENT IS READY !

fig.12

Fly poles

Roof poles

Wall poles

2.Assemble the shock corded poles and divide according to size and shape. Take care; make sure that each pole section is fully seated into the next. Do not allow the sections to snap together as this can damage the ends. See fig 2.

fig 7

fig 2

3.Insert both roof poles into the sleeves sewn on the tent body. They should run corner to corner crossing in the center.

Fit one end of each into a nylon elbow attached to the roof corners at A and B. Move to the opposite side, arch the poles and again fit into the nylon elbows at C and D.

See fig 3 and 4.	C	D
fig 3
B
fig 4		A
		NOTE: One arm of each elbow has interior
		ribs. The roof pole inserts into this ribbed
		arm. The wall pole inserts into the plain
		arm.

6.Attach the fly to the poles. Lay out the fly with the inside side up, on ground at the front of the tent, near the door.

Fit the fly poles into the pockets sewn to the hem. The poles form an x crossing in the center of the fly. Secure the fly to the poles by wrapping all five of the hook and loop fasteners around the fly poles. See fig 8, 9 and 10.

fig 8

fig 10 fig 9

fig 13

Guy Out: This tent has very large straight walls that act differently in high winds. If there are high winds, carefully follow the guy out instructions on the back side of this sheet.

Awning: If it's raining, lower both corner awning poles to create run-off channels. Loosen shockcord on each corner pole, lower the angle of each pole and re-tighten guy lines.

Power Port: Open zipper and run extension cord through opening. Close zipper so that it rests next to the extension cord. Make sure the zipper cover is not twisted or tucked. The cover must lay flat against the outside of the tent to keep out rain.

Take Down: Pull up all stakes. Release the fly's hook & loop straps. Remove fly. Remove fly poles. Remove clips from wall poles and pull poles off of the pins. Remove roof poles. Collapse all poles and stow. Fold the tent onto itself then fold the fly and lay it on tent. Roll up both towards the open door and stow.

Sweep Out: Inside, at the bottom center of each
door is a sewn-in web loop. Pull this loop to the
outside and stake it down to provide a ready	fig.14
exit for floor sweepings. See fig 14.
Options: Floor Saver and Gear Loft

REV B 4.09