Euro-Pro CW230H Cleaning The Cyclonic Attachment, Cleaning / Replacing Foam Inlet Filter

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

7.If you still see that the pre-cleaner has not been completely removed, repeat steps 3 and 4 again.

8.If the stain has not been removed, repeat steps 1 to 6 again.

NOTE: Pre-cleaner spot removers sometimes do not remove tough stains. Please use a professional carpet cleaning service if such is the case.

Cleaning The Cyclonic Attachment

1.Do not allow dirt to go above the “MAX” level.

2.Remove the cyclonic attachment from flexible hose and any extension tubes.

3.Hold cyclonic dust cup firmly and turn the cover counter clockwise to unlock. (Fig.7)

4.Firmly pull apart and empty dust cup. (Fig. 8)

Dust Cup

Lock

Fig. 8

Fig. 7

5.Dust cup may be rinsed under lukewarm tap water. Ensure that dust cup is dry before using. (Fig. 9)

Fig. 9

Cleaning / Replacing Foam Inlet Filter

1.Unplug unit from electrical wall outlet.

2.Lift the locking tabs on either side of the water tank.

3.Lift the handle to remove the removable cover. (Fig. 11) Empty the water tank into a toilet or an outside drain.

4.The foam inlet filter should be cleaned regularly depending on

amount of usage. Carefully remove the foam inlet filter.

A severely soiled or

clogged filter should be thoroughly washed with fresh tepid water. A mild detergent may be used if required.

5.Let the foam inlet filter air dry completely

before replacing in vacuum. Do not use a washing machine to rinse the

filter. Do not use a hair dryer to dry it. Air dry only. Never operate the vacuum without the foam inlet filter in place.

6.The water tube may become clogged with debris. Pull away from removable cover and rinse under lukewarm water and replace. (Fig. 12)

Cover

Pre-motor

Filter

Removable

Using Your Water Filtration Vacuum For Dry Vacuuming

NOTE: Always remove the power plug from the wall outlet before assembling or removing accessories and/or filling or emptying the water tank.

1.Add 3 cups, (24 oz) of water to the tank.

2.Insert plug into electrical outlet.

3.To connect the flexible hose into the air intake duct, align the arrow on the hose with the arrow on the unit. Push in and turn 90° clockwise to lock the hose in place. (Fig. 1)

4.Attach the flexible hose to the cyclonic tube. (Fig. 1)

5.Push extension tube into the cyclonic air intake opening and attach desired accessory to the other end. (Fig. 1)

Cyclonic

attachment

Air intake

duct

Extension

tube

Accessory Fig. 1

WARNING: Water level MUST NEVER exceed the "Max" level indicated on the

6.Turn the "On/Off" Switch to the "On" position.

7.The flexible hose is equipped with a manual suction control to adjust the amount of suction required. For strong suction ensure that suction button is closed. To decrease amount of suction slide the button to open until desired strength is obtained. (Fig. 3)

Manual

Suction

Control

Fig. 3

To Use the Dry Vac Feature Without the Cyclonic Attachment:

8.Attach the wider end of one of the extension tubes to the flexible hose handle.

9.Attach the other extension tube to the first one and ensure a tight connection.

10.Attach the desired accessory to the narrow end of the extension tube.

11.When finished using the unit, unplug from electrical outlet and empty the water from the unit.

Accessories for Use With the Dry Vac Feature:

• Air Driven Turbo Brush
•	Convertible Brush
•	Crevice Tool
•	Floor Brush
•	Cyclonic Attachment

WARNING: To reduce risk of electric shock - unplug before cleaning or emptying water tank.

Foam Inlet

Filter

Cover

water tank. Empty tank when water level reaches "MAX" indicator. If water is seen to be coming from the exhaust - immediately turn the unit off and unplug

Emptying & Cleaning Water Tank WARNING: Water level MUST NEVER

exceed the "Max" level indicated on the water tank. Empty the tank

when the water level reaches "MAX" indicator. If water is seen to be coming from

the exhaust - immediately Fig. 10 turn the unit off and unplug from electrical outlet. Empty the water tank and clean.

(Fig. 10) Refill water tank with clean water to min. 3 cup level, then plug unit back in and continue working.

Canister

Locking

Fig.11Tabs

Water Tube

Water Tube

Fig. 12

6

from electrical outlet. Empty water tank and clean. Refill water tank with 3 cups (24 oz.) of clean water then plug unit back in and continue working. IMPORTANT: DO NOT operate this vacuum when water level is below the water tube opening.

Water Tube

Fig. 2

3