Using The Accessories For Dry
Vacuuming
Cyclonic Attachment
The cyclonic attachment is for dry vacuuming only. This attachment captures dust and dirt particles. You must use at least one extension tube with the cyclonic filter tube, along with the desired accessory.
Convertible Brush
For vacuuming high, hard to reach places such as ceilings, curtains/drapes, etc., use the convertible brush with removable bristles as follows:
1.Insert the convertible brush to the hose alone or with the extension tube attached to the hose.
2.If you need a brush action, slide on the removable bristle brush onto the deluxe brush. (Fig. 4)
Fig. 4
Crevice Tool
For hard to reach areas use crevice tool with cyclonic dirt tube and extension tube or directly onto flexible hose.
Floor Brush
NOTE: The floor brush is only intended for dry vacuuming. Use with the cyclonic attachment or directly on the hose with extension tubes in place.
•The bristles under the floor brush can be left in the “Down” position for use on carpets or can be
lifted to the “Up” position for vacuuming floors. (Fig. 5)
Fig. 5
Air Driven Turbo Brush IMPORTANT: Do not use the Air Driven Turbo Brush for wet pick-up.
The air driven turbo brush removes embedded dust and pet hair. The efficiency of your air driven turbo brush depends on the bristle brush rotating at high speed. Strong air suction is needed
to accomplish this. In order to ensure that maximum air suction is maintained, please read the following instructions:
1.Empty the water tank and cyclonic dust cup frequently.
2.Ensure that the rotating brush is kept free of hair and string which may accumulate and decrease brush performance.
3.Keep air driven turbo brush turbine free of dirt and foreign matter. (See illustration for cleaning instructions.)
Locking Latch
Tilt
Upwards
Turbine
Cleaning Air Driven Turbo Brush
From time to time, the turbine of your turbo brush will require cleaning. To do this:
1.Remove the turbo brush from the hose or extension tube.
2.Slide locking latch forward then tilt the top housing of the brush upwards. The top housing is hinged and will tilt up approximately 45° only.
3.There may be some dust, lint, hair, etc on the turbine wheel. Remove as much of this as possible.
4.You may also use the unit’s hose with crevice tool attached and use the vacuum to remove any additional debris from the turbine.
5.Ensure that the turbine wheel moves freely by rotating it with your finger. If the turbine does not rotate, call
1 (800) 798-7398 for help.
6.Once clean, close the top cover of the turbo brush and slide the locking latch toward the rear of the brush to lock.
Using Your Water Filtration
Vacuum for Wet Pick-Up
WARNING: When using your vacuum for wet vacuuming empty water tank and remove cyclonic attachment before vacuuming. DO NOT use vacuum with cyclonic attachment when using vacuum for wet pick-up.
WARNING: Water level MUST NEVER exceed the "Max" level indicated on the water tank. Empty tank when water level reaches "MAX" indicator. If water is seen to be coming from the exhaust - immediately turn the unit off and unplug from electrical outlet. Empty water tank and clean. IMPORTANT: This unit is supplied with a safety feature that will stop air flow if the tank is overfilled. If the airflow is stopped, shut off vacuum, empty tank, reassemble vacuum and continue.
1.Add 3 cups, (24 oz) of water to the tank.
2.Insert plug into electrical outlet.
3.To connect the flexible hose into the air intake duct, align the arrow on the hose with the arrow on the unit. Push in and turn 90° clockwise to lock the hose in place. (See Fig. 1 on Page 3)
4.Attach the flexible hose to the canister. (See Fig. 1 on page 3)
5.Push extension tube into the cyclonic air intake opening and attach desired accessory to the other end. (See Fig. 1 on page 3)
6.Turn the "On/Off" Switch to the "On" position.
7.The flexible hose is equipped with a manual suction control to adjust the amount of suction required. For strong suction ensure that suction button is closed. To decrease amount of suction slide the button to open until desired strength is obtained. (See Fig. 3 on page 3)
8.Select and attach accessory to the other end of flexible
hose. If an extended reach is desired attach one or more
extension tubes directly to flexible hose. (Fig. 6)
Fig. 6
9.If there is a large volume of liquid to be picked up, empty tank regularly. DO NOT allow tank to overfill.
10.If water is escaping from the exhaust shut off unit immediately and empty the tank before resuming.
Accessories for Use With the Wet Pick-Up:
•Small Squeegee
•Large Squeegee
•Triangular Water Brush
Using the Accessories for Wet Vacuuming
NOTE: Never use the Cyclonic Attachment when using the vacuum for wet pick-up.
Large Floor Squeegee
The large floor squeegee is excellent for small spills on floor surfaces. Can
be used directly onto flexible hose or with extension tube.
Small Floor Squeegee
The small squeegee is good for small tight areas.
Triangular Water Brush
The triangular water brush is best for spot cleaning on carpets.
Hints for Spot Cleaning Carpets Note: Before spot cleaning your carpet with the triangular brush, test for color fastness. Dampen a white cloth with the cleaning solution that you will be using and test a small area in a closet or under a piece of furniture. Gently rub the cloth over the area. Check each color for bleeding. If the cloth remains white, it should be safe to clean the carpet or upholstery. When using commercial pre-cleaners spot removers, follow manufacturers instructions and follow this procedure with vacuum.
1.Apply the pre-cleaner spot remover to the carpet as per manufacturers instructions.
2.Using the triangular water brush, suck the pre-cleaner spot remover liquid from the carpet.
3.Spray the same area with water.
4.Vacuum again to remove the water.
5.Repeat steps 3 and 4 again if necessary.
6.Empty the water tank.
