OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS (CONT.)This appliance is for HOUSEHOLD USE
ONLY and may be plugged into any
120V AC polarized electrical outlet. Do
not use any other type of outlet.
4. Turn the temperature dial to any of
the temperatures within the gray
steam band and allow the iron to
heat for approximately 2 minutes
before ironing. Place iron on a
stable, protected surface while the
iron is warming to the desired
temperature.
5. Slide the steam lever up to increase
the amount of steam. When using
extra steam, the iron uses more
water and it may be necessary to fill
the tank more often. See Figure 3.
WARNING! Before filling the iron
with water, be sure the iron is not
plugged into the electrical outlet. The
iron may be filled with water while it
is hot.
2. Set the temperature dial to the
"MAX" position. Place the iron on a
stable surface and allow it to heat for
approximately 2 minutes.
3. With the iron in a horizontal position,
press the burst of steam button
several times to prime the pump.
See Figure 4.
DRY IRONING WARNING! TO PREVENT THE RISK
OF BURNS, use caution when filling
iron with water. Burns can occur
from touching hot metal parts, hot
water, or steam.
NOTE: Because of the soleplate design,
ordinary tap water may be used with this
iron. However, in very hard water areas,
we recommend using distilled or
demineralized water.
CAUTION: Never fill the iron with
fabric conditioner, starches or any
other liquid, as these will damage the
steam mechanism. Do not use
contaminated water.
1. Turn temperature dial to “MIN” and
slide lever all the way down.
2. Holding the iron at a slight angle,
pour water slowly into the water
filling inlet. See figure 2. Fill tank to
desired level or to the “MAX” water
level marking using the water filling
flask. (When the iron is upright, the
transparent water tank allows you to
gauge the amount of water.) DO
NOT overfill the tank.
All marked settings on the temperature
dial can be used for dry ironing. Slide
the variable steam control lever all the
down as shown in Figure 1. This will cut
off the steam flow if water is in the tank.
For Dry Ironing:
For Steam Ironing:
Figure 4
NOTE: If the tank runs dry, remove the
plug from wall outlet. Then, fill the iron
with water and re-prime the pump. The
iron may be filled with water while it is
hot.
WATER SPRAY
1. Turn temperature dial to “MIN” and
slide the variable steam control lever
all the way down to "0" mark.
2. Plug the cord into a polarized, 120V
AC electrical outlet. The power “ON”
light will come on, indicating that the
iron is receiving power.
3. Turn the temperature dial to the
desired setting. (See “Ironing Guide”
for a guide to temperature selection.)
4. Place iron vertically on a stable,
protected surface while iron is
warming to desired temperature.
Figure 1
The water spray is useful on fabrics with
stubborn wrinkles. Press the spray
button and a jet of water will spray onto
the fabric being ironed. See Figure 5.
The water spray can be used with dry or
steam ironing as desired.
Figure 3
BURST OF STEAM
WARNING! DO NOT aim iron at face,
towards yourself, or anyone else
while using or adjusting steam.
Burns or serious injury may occur.
The burst-of-steam button is useful
when ironing denim, cotton, and linens.
It provides extra, sudden blasts of
steam which aid in removing stubborn
wrinkles.
The burst-of-steam feature can be used
with Dry or Steam ironing as desired.
1. Make sure the water tank is at least
1/2 filled with water.
STEAM IRONING
WARNING! DO NOT aim iron at face,
towards yourself, or anyone else
while using or adjusting steam.
Burns or serious injury may occur.
3. Plug the cord into a polarized, 120V
AC electrical outlet.
Figure 2
5
Figure 5
6