Euro-Pro SV800C Operating Instructions, On/Off Switch, Converting Stick Vac to Hand Vac

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Charging the Battery NOTE: The battery is packaged separately from the charging base but it is not charged. Before using the vacuum, charge the battery for 24 hours. NOTE: The charging base can be mounted on a table top or a wall near an electrical outlet.

1.	When mounting on a wall, make sure
	that the intended wall area for the
	charging base to be drilled is free
	from any hidden electrical wires,
	water pipes and gas lines.
2.	Select an appropriate place close to a
	wall power outlet (120V., 60 Hz).
3.	Do not place near direct sunlight,
	near a heat source or outdoors.
4.	Select an appropriate drill type for the
	material to be drilled.
5.	Carefully measure and mark the
	location of all bracket holes and then
	drill holes and screw the charging

4.Once the telescopic tube is inserted, you can adjust the height of the handle by moving the locking latch past 90 degrees to the open position. Holding the handle, extend the tube to the height that is right for you and then close the latch to the locked position. (Fig. 3)

Fig. 2 Fig. 3

On/Off Switch

The On/Off switch has three different positions. (Fig. 5)

1.Push on the "I" side to turn the vacuum to “LOW” speed.

2.Push on the “II" side to turn the vacuum to “HIGH” speed.

3.Push on the “O” (middle) to turn the vacuum to the “Off” position.

=ON (Low speed)

=OFF

=ON (High speed)

Fig. 5

Converting Stick Vac to Hand Vac

1.	Press the telescopic release button to
	remove the telescopic tube. (Fig. 6)
2.	Press the floor brush release button

Emptying the Dust Cup IMPORTANT: Always turn the vacuum off before removing the dust cup.

1.To remove the dust cup, press the dust cup release that is on the bottom of the dust cup. (Fig. 8)

Dust cup

release

Fig. 8

	base onto the wall. (Screws not
	included.)
6.	The charge adapter plug is keyed and
	will fit into the charging base only one
	way. Align the channel on the
	adaptor plug with the tab on the
	bottom of the charging base. (Fig. 1)
7.	Plug the charging adapter into the
	closest electrical wall outlet.
8.	Place the charging base onto the wall.
	Be careful not to pinch the charging
	adaptor wire between the wall and the
	charging base.
9.	Insert the battery into the charging
	base to charge. The charging light on
	the charging base will light up.

Charger base

BatteryCharging

adapter

Charging light

Fig. 1

Assembling the Stick Vac

1. Remove all the parts of the stick vac from the box.

2. Hold the motorized brush and push it in the base of the stick vac completely. (Fig. 2)

NOTE: The battery must be charged for 24 hours prior to first use. Ensure that the On/Off switch is in the “Off” position before inserting the battery.

5.Hold the battery and insert the bottom part first into the opening found at the back of the unit. Then rotate in place making sure that it clicks into place.

(Fig. 4)

Fig. 4

6.Turn the unit “On” to begin vacuuming.

7.Place your foot lightly on the top of the motorized brush and rotate the handle back toward you to release the unit from the locked upright position.

and remove the motorized floor

brush. (Fig. 6)

Lift

Telescopic

tube release

Release

button

Pull Fig. 6

3.Insert the crevice tool into the bottom of the vacuum making sure that it snaps into place. (Fig. 7) To remove the crevice tool, press the motorized brush/crevice tool release button.

2.Hold the dust cup cover and twist it to the left to remove it from the dust cup. (Fig. 9)

3.Hold it over a garbage can and empty the dust. (Fig. 10)

IMPORTANT: Empty the dust cup after every use. Never use the vacuum without the dust cup and filter

in place.

4.To reattach the dust cup cover, align the indicators that are the cover and the dust cup and turn to the right to lock in place. Make sure that the “▼” symbol on the top cover is aligned with the “▲” symbol

on the dust cup to lock into place. (Fig. 11)

Fig. 9

Fig. 10

3. Hold the telescopic tube and push it in to the top of the handle of the stick vac. (Fig. 3)

3

Fig. 7

4

Fig. 11