Fig. 9
Fig. 10

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Carpet Height Selector

This upright vacuum can be used on multiple types of carpeting, bare floors or upholstery with attachments.

To select a pile height setting:

1.Turn vacuum cleaner "Off".

2.Select a pile height setting by sliding the carpet height selector to the desired setting. (Fig. 4)

Fig. 4

Suggested Pile Height Setting:

You may need to raise the height of the vacuum to make some jobs easier, such as scatter rugs and longer pile carpets. Suggested settings are:

HIGH: shag carpet, long pile, plush scatter rugs, tools

MED: medium to long pile

LOW: short to medium pile, bare floors

FLOOR: very low pile, bare floors

Place unit in "HIGH" setting when using attachments to prevent possible floor damage. Always set the Carpet to Floor selector to “Floor” setting when using the accessories. (Fig. 5)

Attention: Special care is required when vacuuming certain types of carpet or floor covering. Always check the carpet or floor covering manufacturer's recommended cleaning instructions before vacuuming.

Removing & Emptying Dust Cup

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, dust cup filter,changing the filters or performing maintenance/trouble shooting checks.

The “Dust Cup” must always be emptied when the dirt level reaches the "FULL" line on the dust cup. To remove the dust cup from the vacuum:

1.Press down on the dust cup release button that is located on the handle of the dust cup. (Fig. 6)

2.Holding the dust cup from the handle, pull the dust cup out from the vacuum. (Fig. 7)

3.To empty the dust cup, hold it by the handle over a garbage can and press on the trap door release button to empty. (Fig. 8)

Fig. 6

Fig. 7

Trap Door

Release

Cleaning the HEPA Dust Cup Filter

IMPORTANT, Please Note : The Rinseable “TapClean” HEPA Dust Cup Filter will stop most of the tiniest dust particles and airborne allergens from re-entering the air you breathe. In fact, it stops 99.97% of all particles as small as 0.3 microns - many times smaller than a human hair!!! Because of this incredible filtration performance, the HEPA Dust Cup Filter will quickly accumulate many fine dust particles inside the white filter folds that are difficult to see but which will eventually block or reduce your suction power - if not cleaned properly. Clean the HEPA Filter after each use as described in this section.

1.To remove the HEPA

filter, remove the dust cup from the unit.

2.To remove the dust cup cover, hold the cover by the handle, turn counter clockwise and lift the cover off. (Fig. 9)

3.Remove the HEPA Rinseable "Tap Clean" filter from the dust cup. (Fig. 10)

4.Vigorously "TapClean" the HEPA dust cup filter on a hard surface until no

more dust is observed falling out. (Fig. 11)

The HEPA filter may also be washed by running it under the tap allowing the water to run on the dirty side. (Fig. 12) We recommend washing it once a month

or when suction appears reduced. Always allow 24 hours for air drying before replacing into the vacuum.

Please Note: The white material in the HEPA filter will discolor over time - This is NORMAL and will NOT affect the performance of the filter.

Warning: Always empty the dust cup and clean the HEPA dust cup filter before each use and during prolonged usage. Never over fill the dust cup - remove dirt and clean the HEPA dust cup filter each time the dust cup is emptied during prolonged usage or risk motor damage.

Cleaning the HEPA Filter Frame

1.Before replacing the HEPA filter in the HEPA Filter frame, you can (should) rinse the frame in lukewarm water by just running it under the tap to remove any dust that is adhering to the frame. (Fig. 13) Do NOT place in dishwasher.

Fig. 13

2.Make sure that the filter frame is completely dry before replacing into the dust cup. Always air dry for 24 hours.

Cleaning the Secondary Filter

1.Underneath the HEPA filter there is a secondary filter.

This is washable in lukewarm water. (Fig. 14) We recommend washing it when you are washing your HEPA filter. Always allow the secondary filter to air dry for 24 hours before replacing into the

vacuum. Never run

Fig. 8

Fig. 11

Fig. 12

the vacuum without Fig. 14 the secondary filter in place.

Fig. 5

5

6

Page 6
Image 6
Euro-Pro UV209B owner manual Carpet Height Selector, Removing & Emptying Dust Cup, Cleaning the Hepa Dust Cup Filter

UV209B specifications

The Euro-Pro UV209B is a sophisticated cleaning device that has garnered attention in the realm of home appliances, particularly for those seeking efficient ways to maintain cleanliness. This vacuum, often recognized for its sleek design and powerful features, combines innovation with user-friendly operation.

One of the main features of the UV209B is its versatility. This vacuum cleaner transitions seamlessly between different floor types, including carpets, hardwood, and tile. Its adjustable suction power allows users to optimize cleaning based on the surface being addressed, ensuring thorough cleaning without damaging delicate flooring.

The UV209B employs advanced filtration technology to enhance indoor air quality. The multiple-stage filtration system captures dust, allergens, and microscopic particles, making it an ideal choice for allergy sufferers. This ensures that while the vacuum is working to clean surfaces, it is simultaneously promoting a healthier home environment.

Another significant characteristic is its lightweight design. Weighing in at a manageable weight, the Euro-Pro UV209B is easy to maneuver, reducing strain on the user during prolonged cleaning sessions. Its ergonomic handle is designed for comfort, facilitating longer cleaning tasks without discomfort, which is increasingly important in today’s busy lifestyles.

Additionally, the UV209B features a convenient bagless design. This not only eliminates the hassle of changing bags but also allows users to easily monitor the dirt and debris collection. The transparent dust bin can be quickly emptied and cleaned, promoting a more convenient and efficient cleaning routine.

In terms of technology, the UV209B incorporates a powerful motor that delivers strong suction power, ensuring that even stubborn dirt and debris are effectively removed. The noise-reducing technology further enhances the user experience, making operation quieter and less disruptive in the home environment.

The Euro-Pro UV209B also comes with a variety of attachments and tools tailored for specific cleaning tasks. These accessories enhance its functionality, allowing users to address tight corners, upholstery cleaning, and more, making it a multi-purpose cleaning solution.

In summary, the Euro-Pro UV209B is a modern cleaning appliance that offers a compelling combination of power, versatility, and user-friendly features. Its thoughtful design and advanced technologies make it a worthy investment for anyone looking to improve their home cleaning routine.