Euro-Pro V1055H How to Start, Carpet Height Selector, Removing & Emptying Dust Cup Container

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

How to Start

The vacuum can be used on multiple types of carpeting or bare floors. When using the crevice tool or dusting brush, place the handle of the vacuum in the upright position.

1. Plug the power cord into the electrical

	outlet.	Store or use
2.	Push the On/Off
	button to the "On"	attachments Use
	position to turn
	the vacuum on.		Clean under
3.	To release the
			furniture
	handle, step
	on the handle		Handle release
	release pedal
	and pull back handle.		Fig. 4

4.When using the crevice tool or dusting brush, the vacuum must be in the upright position. (Fig. 4)

Carpet Height Selector

This upright vacuum can be used on multiple types of carpeting and bare floors. To select a pile height setting:

1.Turn vacuum cleaner "Off".

2.Select a pile height setting by rotating the carpet height selector to the desired setting. (Fig. 5)

Carpet height selector

Fig. 5

Suggested Pile Height Setting:

You may need to raise the height of the vacuum to make some jobs easier, such as scatter rugs and longer pile carpets. Suggested settings are:

HIGH: shag carpet, long pile, plush scatter rugs, tools

MED: medium to long pile

LOW: very low pile, bare floors

Place unit in “UPRIGHT" position when using attachment or hose to prevent possible floor damage. Always set the carpet height selector to “highest” setting when using the accessories and hose.

Attention: Special care is required when vacuuming certain types of carpet or floor covering. Always check the carpet or floor covering manufacturer's recommended cleaning instructions before vacuuming.

Removing & Emptying Dust Cup (Container)

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup (container), dust cup HEPA-Type filter, changing the pre-motor filter or performing maintenance/trouble shooting checks.

Important: Do NOT use the vacuum without ALL the filters in place.

The “Dust Cup (Container)” must always be emptied when the dirt level reaches the “FULL" line on the dust cup (container). To remove the dust cup

(container) from the vacuum:

1.Press down on the dust cup release button that is located on the dust cup cover handle of the dust cup. (Fig. 6)

Dust Cup

Release Button

Fig. 6

2. To empty the dust cup container,

hold the dust cup from the handle

over a garbage container and press

on the trap door release button that is

on the back side of the dust cup

container to release the dust cup

Trap Door

Release Button

Fig. 7

•The dust cup container can be washed in lukewarm water.

•Do not use strong detergents.

•Ensure that the dust cup container is fully dry before putting back on the vacuum cleaner.

•Do not wash in dishwasher.

Cleaning the HEPA Filter and the Filter Frame

Warning: After each Use - Always remove the Filter Assembly, then vigorously tap clean the HEPA-Type Filter until no more dust can be removed.

IMPORTANT, Please Note: The

Rinseable “TapClean” HEPA-Type Dust Cup Filter will quickly accumulate many fine dust particles inside the white filter folds that are difficult to see but which will eventually block or reduce your suction power - if not cleaned properly. Clean the HEPA-Type Filter after each use as described in this section.

1.To remove the filter assembly from the dust cup, hold the dust cup cover from the handle in one hand and with the other hand, turn the dust cup container counter clockwise. (Fig. 8)

Open

Mark

Arrow

for

alignment

2.Remove the filter assembly from the dust cup container.

3.To separate the filter assembly, hold the bottom of the filter frame and pull the HEPA-Type filter out.

(Fig. 9)

Filter Assembly

HEPA-Type

Filter

Filter

Ring

Filter

Frame

Fig. 9

4.Remove the filter ring that is around the

HEPA-Type filter. Then vigorously “TapClean” the

HEPA-Type Filter on a hard surface until no more dust is observed falling out.

5.To clean the filter frame, we recommend that you rinse it under lukewarm running water to remove the dirt that accumulates

on it, but always

allow 24 hours to air dry before inserting back into the vacuum.

6.To re-assemble the filter assembly, insert the filter ring over the HEPA-Type filter and then insert the HEPA-Type filter assembly into the filter frame. Replace the filter assembly into the dust cup container. Replace the dust cup container cover.

bottom. (Fig. 7)

Fig. 8

5

6