Manuals / Everpure / Household Appliance / Water System

Everpure ENVI-RO installation and operation guide Control system operation

Models: ENVI-RO

1 16
Download 16 pages 50.69 Kb
Page 4
Image 4

Control system operation

The ENVI-RO system includes a micro-processor based control system that monitors system conditions and controls the system operation. A digital display panel provides operational information and 4 buttons provide operator access. To follow is a list of modes and a description of each function. Use this as a guide during start- up, normal operation and when service is required.

Operational Mode

•MAIN SCREEN VIEW - When the system is in normal operation and not operating in any of the following operational modes, the panel will display the system identification with software version and total run hours since start-up, or last reset.

•PRESSURIZE - When pressure in the storage tank drops below the pressure switch “on” setting, the system will start processing water and refill the storage tank. Once the pressure in the storage tank rises above the pressure switch “off” setting, the system will stop. Run time in seconds will be displayed.

•FLUSHING - If the ENVI-RO System remains idle for the programmed length of time, the control system will automatically go into FLUSHING mode. During this time, there will be flow to drain (reject). Remaining flush time in seconds will be displayed.

•REFILL - At the end of FLUSHING, or if pressure drops too low in the storage tank during FLUSHING, the control will enter REFILL mode. Run time in seconds will be displayed.

Programming Mode

The ENVI-RO Controller has several user accessible menu’s. This menu “loop” allows for adjustment of several variable parameters. The Controller has 4 buttons below the display for these adjustments. Description of the button functions are shown in the digital display area.

•Press and hold any key for 3 seconds to enter set-up mode.

•Flush Time X1 - This parameter determines the flush duration. Upon determining the recovery and reject flow, a time value in seconds is entered for this setting. Range is 0-995 seconds in 5 second increments. Use the +/- keys to adjust this value. Press Enter to save value and go to next screen.

•Flush Int X2 - This parameter determines the flush interval. If the system does not process water for the time value selected, the system will enter FLUSHING mode. A time value in hours is entered for this setting. Range is 0.5 to 10 hours in 0.5 hour increments. Use the +/- keys to adjust this value. Press Enter to save value and go to next screen.

•Reset Total Hr? - This parameter allows resetting the total run time, which is displayed in the MAIN SCREEN VIEW. Press YES to reset, NO to NOT reset. Controller saves selection and goes to next screen.

•Coffee Setup? - This parameter allows viewing the TDS reading in the coffee outlet line, with a very frequent up-date rate. Use this mode when adjusting the blend valves. Select YES to enter this mode, and NO to exit programming.

•Coffee TDS: - This is a view only screen. The value displayed is the TDS level of the water in the Coffee outlet line. The most accurate readings are attained by having flow on the Coffee line. Press any key to return to the MAIN SCREEN VIEW.

•SAVING DATA... - This is a view only screen. The controller is saving the settings and returning to the MAIN SCREEN VIEW. If desired, press and hold either middle button to enter TDS Calibration mode.

•TDS CAL - This parameter allows adjustment of the TDS value the controller will display. Use this mode to calibrate the system with a calibration solution. Use the +/- keys to adjust this value. Press Enter to save and return to the MAIN SCREEN VIEW.

Electrical Connections

The system is pre-wired at the factory. Verify that a 115 VAC ground fault protected circuit rated at 15 Amps minimum is located nearby. Plug-in power cord when instructed to do so in the following section.

ENVIRO V. X.XX

TOTAL: XXXX.XX Hours

PRESSURIZE... XXXXX

FLUSHING... XXXX

REFILL... XXXX

ENVIRO V. X.XX

TOTAL: XXXX.XX Hours

Flush Time X1

- Enter +

Flush Int X2

- Enter +

Reset Total Hr?

Yes No

Coffee Setup?

 

Yes

No

Yes No

 

 

 

 

Coffee TDS: XXX

PRESS TO RETURN

SAVING DATA...

TDS CAL XXX - Enter +

4

Page 3 Page 5
Page 4
Image 4
Everpure ENVI-RO installation and operation guide Control system operation
Page 3 Page 5

ENVI-RO specifications

The Everpure ENVI-RO is a revolutionary reverse osmosis water filtration system designed to deliver high-quality drinking water while ensuring exceptional taste, safety, and convenience. Ideal for residential settings, this advanced system employs cutting-edge technology to remove impurities, contaminants, and unwanted minerals, providing users with clean and refreshing water.

One of the standout features of the ENVI-RO is its multi-stage filtration process, which includes a pre-filter, reverse osmosis membrane, and post-filter. The pre-filter effectively captures larger particles and sediments, prolonging the life of the subsequent filters. The heart of the system, the reverse osmosis membrane, boasts a high rejection rate for a wide range of contaminants, such as chlorine, lead, fluoride, and nitrates, resulting in water that is not only pure but also tastes fantastic.

The post-filter further enhances the quality of the water by removing any remaining odors and tastes, ensuring that each drop is crisp and clean. The ENVI-RO system also features an integrated water storage tank that provides ample supply, delivering filtered water on demand. The tank is designed to minimize space, making it an ideal choice for kitchens with limited under-sink areas.

Another notable characteristic of the Everpure ENVI-RO is its ease of installation and maintenance. Designed with user-friendliness in mind, the system can be installed without the need for professional assistance, allowing homeowners to enjoy high-quality water quickly and efficiently. The filters are easily replaceable, and the system includes a convenient indicator light that alerts users when it’s time for a filter change, ensuring optimal performance at all times.

Durability and reliability are also key components of the ENVI-RO design. The system features high-quality materials that ensure long-lasting performance, coupled with a design that minimizes wastewater during the filtration process, making it an environmentally friendly choice.

Whether for cooking, drinking, or preparing beverages, the Everpure ENVI-RO provides a superior solution for families seeking the best in water quality. With its innovative technologies and user-centric features, the ENVI-RO system stands as a testament to Everpure's commitment to delivering clean, delicious water that enhances everyday living.