Everpure ENVI-RO installation and operation guide Installation and Operation Guide, Introduction

Installation and Operation Guide

Introduction

The Everpure ENVI-RO™ Mineral Reduction System is a pre- engineered, pre-assembled Reverse Osmosis (RO) system designed to provide high purity water for multiple applications, such as premium espresso, coffee, blended beverages and steam, to name a few. It combines a number of water treatment technologies into one easy to install package. The system provides superior protection against taste and odor causing contaminants while removing dirt, particulates and dissolved solids that can foul or scale equipment.

Initial System Production

Water production depends on supply water pressure and temperature. See PERFORMANCE section (page 8) for normalized production.

Influent Water Characteristics

The following table lists the allowable operating range of various water properties within which the ENVI-RO™ will function properly.

Total Dissolved Solids (TDS)	0	-1,000 ppm (0-1,000 mg/I)
pH	5	-10
Chlorine1	0	-3 ppm (0-3 mg/I)
Chloramines	0	-3 ppm (0-3 mg/I)
Turbidity	0	-1 NTU
Iron	0	-1 ppm (0-1 mg/I)

1Reverse osmosis membrane filter used in this system will be damaged by chlorine. An activated carbon filter should be provided with this system to protect the reverse osmosis membrane from chlorine attack. Influent chlorine should not exceed 3 mg/I.

The system consists of 5 major components:

1.2SR-BW Water Conditioning cartridge

2.Dual-Head booster pump

3.MR-600 Reverse Osmosis (RO) membrane cartridge.

4.6-Gallon RO Water Storage Tank

ENVI-RO™ High Efficiency Reverse Osmosis System

Mineral Reduction System For Foodservice Applications

Operating Specifications

•Dynamic Operating Pressure: 25-80 psi (1.7-5.5 bar)

•Static Operating Pressure: 100 psi (6.9 bar)

•Operating Temperature 40-100°F (4.4-37.8°C)

•Connections

Inlet/Outlet: 3/8-inch OD tube (John Guest© Push-in)

Concentrate: 3/8-inch OD tube (John Guest© Push-in)

Electrical: 115 volt AC / 60 Hz / 1 Phase Ampere:

Stand-by: 0.2

Flush: 0.5

Run/Fill: 2.7

Branch Circuit Protection: 15 or 20 AMP Ground Fault Protected

Pre-Installation Checklist

5. Control System with Power Supply

The 2SR-BW Water Conditioning cartridge contains media that reduces the scaling tendency of hard water minerals found in many water supplies, extending RO membrane life.

The Dual-Head booster pump increases the inlet pressure to maintain consistent permeate production, plus eliminates back- pressure on the permeate output. This innovative approach to both boosting and eliminating back-pressure allows for maximum system efficiency.

The MR-600 RO membrane cartridge contains a semi-permeable reverse osmosis membrane. Here, most dissolved impurities are separated from the water and flushed down the drain. The water that is able to pass through the membrane, which is very low in dissolved impurities, is referred to as permeate, RO water, or product water.

Once the RO water is produced, it is stored in the 6-Gallon RO Water Storage Tank. This tank serves two key functions; 1) It acts as a buffer between the system and the connected equipment, providing ample volumes of water instantaneously, 2) It reduces the on-off cycling of the RO system, which produces better quality water, and prolongs the system’s life.

1.Can the unit be mounted within a reasonable distance of the water supply and drain facilities?

2.Is there an un-switched 115 VAC GFIC (ground fault interrupter circuit) protected receptacle available for powering the system?

3.Is there adequate clearance and support to install the unit and permit access for maintenance? The total system weight will vary based on model and storage tank selected. See specification table for approximate operating weights.

4.Does the inlet water supply meet the requirements listed below?

a.A minimum of 25 PSI pressure on a consistent basis

b.Less than 1,000 ppm of Total Dissolved Solids (TDS)

c.pH level between 7.0-9.0

d.Turbidity less than 1 NTU

Printed in U.S.A. EV3128-25 Rev A SE08